Table of Contents
Advertisement
SDM-300L3 Satellite Modem
Remote Control Operation
TX Channel
Command:
Data Phase
Response:
(Channels
#3 and #4)
Status:
Response:
RX Channel
Command:
#1 Enable
Response:
Status:
Response:
RX Channel
Command:
#1 Data
Response:
Rate
Status:
Response:
RX Channel
Command:
#2 Enable
Response:
Status:
Response:
RX Channel
Command:
#3 Enable
Response:
Status:
Response:
RX Channel
Command:
#3 Data
Response:
Rate
Status:
Response:
RX Channel
Command:
#4 Enable
Response:
Status:
Response:
RX Channel
Command:
#4 Data
Response:
Rate
Status:
Response:
<add/TCDP_x_yyy'cr'
>add/TCDP_x_yyy'cr''lf']
<add/TCDP_x'cr'
>add/TCDP_x_yyy'cr''lf']
<add/RCEN_1_xxxx'cr'
>add/RCEN_1_xxxx'cr''lf']
<add/RCEN_1'cr'
>add/RCEN_1_xxxx'cr''lf']
<add/RCDR_1_xxxx.x'cr'
>add/RCDR_1_xxxx.x'cr''lf']
<add/RCDR_1'cr'
>add/RCDR_1_xxxx.x'cr''lf']
<add/RCEN_2_xxx'cr'
>add/RCEN_2_xxx'cr''lf']
<add/RCEN_2'cr'
>add/RCEN_2_xxx'cr''lf']
<add/RCEN_3_xxxx'cr'
>add/RCEN_3_xxxx'cr''lf']
<add/RCEN_3'cr'
>add/RCEN_3_xxxx'cr''lf']
<add/RCDR_3_xxxx.x'cr'
>add/RCDR_3_xxxx.x'cr''lf']
<add/RCDR_3'cr'
>add/RCDR_3_xxxx.x'cr''lf']
<add/RCEN_4_xxxx'cr'
>add/RCEN_4_xxxx'cr''lf']
<add/RCEN_4'cr'
>add/RCEN_4_xxxx'cr''lf']
<add/RCDR_4_xx.x'cr'
>add/RCDR_4_xx.x'cr''lf']
<add/RCDR_4'cr'
>add/RCDR_4_xx.x'cr''lf']
Where:
x = 3 or 4 (channel number).
yyy = NRM (normal data phasing) or INV (inverted data
phasing).
Where: xxxx = OFF (Disabled), DI (D&I Enabled), T1E1
(T1/E1 Enabled).
Note: This command enables channel #1 for D&I
operation, T1/E1 operation, or can be disabled.
Where: xxxx.x = 1544.0 or 2048.0 kbps for T1/E1
operation. N * 64.0 kbps for D&I operation.
Where: xxx = OFF (ADPCM Disabled), ON (ADPCM
Enabled).
This command enables channel #2 for ADPCM operation,
or can be disabled.
Where: xxxx = OFF (Channel Disabled), AUPC (Channel
Enabled for AUPC), A232 (Channel Enabled for ASYNC
RS232), S232 (Channel Enabled for SYNC RS232), A422
(Channel Enabled for ASYNC RS422), S422 (Channel
Enabled for SYNC RS422).
Note: This command enables channel #3 for
SYNC/ASYNC RS232/RS422 operation, AUPC operation,
or can be disabled.
Where: xxxx.x = 0.6 to 4000.0 for Sync. RS422 (kbps in
100 bit/s steps). 0.6 to 64.0 for all other modes (kbps in
100 bit/s steps).
Where: xxxx = OFF (Channel Disabled), AUPC (Channel
Enabled for AUPC), A232 (Channel Enabled for ASYNC
RS232), S232 (Channel Enabled for SYNC RS232), A485
(Channel Enabled for ASYNC RS485).
Note: This command enables channel #4 for
SYNC/ASYNC RS232 operation, ASYNC RS485
operation, AUPC operation, or can be disabled.
Where: xx.x = 0.6 to 64.0 (kbps in 100 bit/s steps).
A–19
Revision 1
MN/SDM300L3.IOM
Advertisement
Table of Contents
