Table of Contents
Advertisement
SDM-300L3 Satellite Modem
Remote Control Operation
IBS Receive
Command:
ESC Type
Response:
Status:
Response:
A.3.4
ODU Configuration Status
Outdoor Unit
Command:
Address
Response:
Status:
Response:
Outdoor Unit
Command:
TX Output
Response:
Status:
Response:
Outdoor Unit
Command:
Power
Response:
Leveling
Status:
Response:
A.3.4
System Configuration Commands
Time Of
Command:
Day
Response:
Status:
Response:
Date
Command:
Response:
Status:
Response:
Remote
Command:
Response:
Clear
Command:
Stored
Response:
Faults
Modem
Command:
Operation
Response:
Mode
Status:
Response:
System
Command:
Modem
Response:
Type
Status:
Response:
Save
Command:
Modem
Response:
Config.
<add/IBSR_xxxxx'cr'
>add/IBSR_xxxxx'cr''lf']
<add/IBSR_'cr'
>add/IBSR_xxxxx'cr''lf']
<add/OADR_'cr'
>add/OADR_xx'cr''lf']
<add/OADR_'cr'
>add/OADR_xx'cr''lf']
<add/ODUO_xxx'cr'
>add/ODUO_xxx'cr''lf']
<add/ODUO_'cr'
>add/ODUO_xxx'cr''lf']
<add/ODUP_xx'cr'
>add/ODUP_xx'cr''lf']
<add/ODUP_xx'cr'
>add/ODUP_xx'cr''lf']
<add/TIME_hh:mmxx'cr'
>add/TIME_hh:mmxx'cr''lf']
<add/TIME_'cr'
>add/TIME_hh:mmxx'cr''lf']
<add/DATE_mm/dd/yyyy'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/DATE_'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/REM_'cr'
>add/REM_'cr''lf']
<add/CLSF_'cr'
>add/CLSF_'cr''lf']
<add/MOM_xxxxxxx'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/MOM_'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/SMT_xxxxxxx'cr'
>add/SMT_xxxxxxx'cr''lf']
<add/SMT_'cr'
>add/SMT_xxxxxxx'cr''lf']
<add/SMC_n'cr'
>add/SMC_n'cr''lf']
Where: xxxxx = DATA (64K DATA) or AUDIO
(2x32K AUDIO).
Note: RX IBS Overhead only.
Where XX = 1 to 15.
Where xxx = ON or OFF.
Where xxx = ON or OFF
Where:
hh = 1 to 12 (hours).
mm = 00 to 59 (minutes).
xx = AM or PM.
Where:
mm = 1 to 12 (month).
dd = 1 to 31 (day).
yyyy = 00 to 99 (year) in 2 - digit year mode, and 1975
to 1999 and 2000 to 2075 in 4 - digit mode.
Configures the modem for remote operation.
The SDM300L will respond to any status request at any
time. However, the SDM300L must be in 'Remote Mode'
to change configuration parameters.
This command is used to clear all stored faults logged by
the SDM300L.
Where: xxxxxxx = TX_ONLY, RX_ONLY, or DUPLEX.
This command configures the modem for simplex or
duplex operation modes. When transmit only mode is
selected, receive faults are inhibited and when receive
only mode is selected, transmit faults are inhibited.
Where: xxxxxx = IDR, IBS, DI, ASYNC, AUPC, EFD,
VSAT, 309 or CUSTOM.
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command saves the current modem configuration for
recall at a later time using the 'RMC_' command. Up to
five different modem configurations can be saved.
A–14
Revision 1
MN/SDM300L3.IOM
Advertisement
Table of Contents
