Chapter 47 Mld Snooping Command List - D-Link DGS-3000 Series Reference Manual

DGS-3000 Series Layer 2 Managed Gigabit Switch CLI Reference Guide
Chapter 47 MLD Snooping Command
The Multicast Listener Discovery (MLD) is used by IPv6 routers to discover multicast listeners on a
directly attached link, much as IGMP is used in IPv4. The protocol is embedded in ICMPv6 instead
of using a separate protocol. MLDv1 is similar to IGMPv2 and MLDv2 similar to IGMPv3.
config mld_snooping [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all ] {state [enable |
disable] | fast_done [enable | disable] | report_suppression [enable | disable] | proxy_reporting
{state [enable | disable] | source_ip <ipv6addr>}(1)}(1)
config mld_snooping querier [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all]
{query_interval <sec 1-65535> | max_response_time <sec 1-25> | robustness_variable
<value 1-7> | last_listener_query_interval <sec 1-25> | state [enable | disable] | version
<value 1-2>}(1)
config mld_snooping mrouter_ports [vlan <vlan_name 32> | vlanid <vlanid_list>] [add | delete]
<portlist>
config mld_snooping mrouter_ports_forbidden [vlan <vlan_name 32> | vlanid <vlanid_list>]
[add | delete] <portlist>
enable mld_snooping
disable mld_snooping
show mld_snooping {[vlan <vlan_name 32> | vlanid <vlanid_list>]}
show mld_snooping group {[vlan <vlan_name 32> | vlanid <vlanid_list> | ports <portlist>]
{<ipv6addr>}} {data_driven}
show mld_snooping forwarding {[vlan <vlan_name 32> | vlanid <vlanid_list>]}
show mld_snooping mrouter_ports [vlan <vlan_name 32> | vlanid <vlanid_list> | all] {[static |
dynamic | forbidden]}
create mld_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr>
delete mld_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr>
config mld_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr> [add
| delete] <portlist>
show mld_snooping static_group {[vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr>}
config mld_snooping data_driven_learning [all | vlan_name <vlan_name> | vlanid <vlanid_list>]
{state [enable | disable] | aged_out [enable | disable] | expiry_time <sec 1-65535>}(1)
config mld_snooping data_driven_learning max_learned_entry <value 1-1024>
clear mld_snooping data_driven_group [all | [vlan_name <vlan_name> | vlanid <vlanid_list>]
[<ipv6addr>| all]]
show mld_snooping statistic counter [vlan <vlan_name> | vlanid <vlanid_list> | ports <portlist>]
clear mld_snooping statistics counter
config mld_snooping rate_limit [ports <portlist> | vlanid <vlanid_list>] [<value 1-1000> | no_limit]
show mld_snooping rate_limit [ports <portlist> | vlanid <vlanid_list>]
show mld_snooping host {[vlan <vlan_name 32> | vlanid <vlanid_list> | ports <portlist> | group
<ipv6addr>]}
47-1 config mld_snooping
Description
This command is used to configure MLD snooping on the Switch.
List
426