Controller - Boss GT-10 Owner's Manual

Parameter/ Explanation
Range
The Assign's operational status is carried
over.
(Example)
If a patch is switched while the volume is
being controlled with the EXP Pedal, the
volume of the subsequent patch will take
on the value determined by the current
On
pedal position (angle).
If the patch switched to has the EXP Pedal
controlling the wah effect, then the vol-
ume assumes the value set in the patch,
and the patch's wah effect is given the
value derived from the current pedal po-
sition (angle).
Pdl Indicate (Pedal Indicate)
You can have all unlit pedal indicators flash faintly instead.
Off The Pedal Indicate function is not use.
On All unlit pedal indicators flash.
Num Pdl Sw (Number Pedal Switch)
This allows you to call up various features by pressing the pedals
with the same numbers as the currently selected patches.
Off This function is not operational.
Tuner Switches the Tuner on and off.
Switches between Preamp channel A and
Ch. A/B
B.
OD Solo Switches the OD/DS SOLO on and off.
Solo Switches the Preamp SOLO on and off.
Switches the preamp SOLO, for both
AB Solo
channel A and B, on and off.
Dial Func (Dial Function)
This setting determines whether or not rotating the dial switches
the patches.
The dial is used both for switching patch-
es and changing the value of settings. In
Pat&Val addition to switching patches with the
pedals, you can also switch them by rotat-
ing the dial.
The dial is used only for changing the val-
Value
ues of settings.
Chapter 8 Parameters Guide

CONTROLLER

Parameter/ Explanation
Range
SYS KNOB SETTING (System Knob Setting)
COMP:Sustain, COMP:Attack,
COMP:Threshld, COMP:Release,
COMP:Level, ODDS:Drive, ODDS:Tone
ODDS:EfectLev, ODDS:Solo Lev,
PRE-A(B):Gain, PRE-A(B):Level
PRE-A(B):Bass, PRE-A(B):Mid
PRE-A(B):Treble, PRE-A(B):Presnce
PRE-A(B):SoloLev, EQ:Low Cut
EQ:Low Gain, EQ:Lo-MidGain,
EQ:Hi-MidGain, EQ:High Gain
EQ:High Cut, DELAY:Time,
DELAY:Feedbak, DELAY:Hi Cut
Knob P1–P4 DELAY:EfctLev, DELAY:D1(2)Time
DELAY:D1(2)Fbk, DELAY:D1(2)HCut
DELAY:D1(2)Lev, CHORUS:Rate
CHORUS:Depth, CHORUS:PreDly
CHORUS:E.Lev, REVERB:Time
REVERB:Hi Cut, REVERB:E.Lev
MASTER:Low, MASTER:Mid
MASTER:High, Patch Level
PDL:Wah E.Lev, PDL:PB E.Lev
SR:Send Level, SR:Rtn Level
NS1(2):Threshold, NS1(2):Release
GLOBAL EQ:Low, GLOBAL EQ:Mid
GLOBAL EQ:Hi
EXP1/2 PEDAL SETTING
Prefernc (Preference)
The patch pedal setting is used. This al-
Patch lows you to use different pedal settings in
each individual patch.
The CONTROLLER screen's pedal set-
ting (Function, Min and Max) is used.
System
This applies the same pedal settings to all
patches.
Function
The function is not assign to the control-
Off
ler.
Foot Volume Controls the Foot Volume.
Pedal Bend *1 Controls the Pedal Bend.
WAH *1 Controls the WAH.
PB/FV *1 Controls the Pedal Bend or Foot Volume.
WAH/FV *1 Controls the WAH or Foot Volume.
Patch Level Controls the Patch Level.
*1 This parameter is enabled in EXP1 PEDAL SETTING.
Min (Minimum)
This sets the minimum value for the
0–100
range in which the parameter can change.
Max (Maximum)
0–100
This sets the maximum value for the
0–200 (Function =
range in which the parameter can change.
Patch Level)
137