YASKAWA GA500 Maintenance & Troubleshooting page 188

3.18 Parameters that Change from the Default Settings with A1-02 [Control Method Selection]
No. Name
Minimum Output
E1-09
Frequency
E1-10 Minimum Output Voltage
Overspeed Detection Delay
F1-09
Time
Motor Overload (oL1)
L1-01
Protection
KEB Start Voltage Offset
L2-31
Level
Stall Prevention during
L3-05
RUN
DC Bus Voltage
L3-20
Adjustment Gain
OVSuppression Accel/
L3-21
Decel P Gain
Current Suppression
L3-36
Gain@Accel
Speed Agree Detection
L4-01
Level
Speed Agree Detection
L4-02
Width
Speed Agree Detection
L4-03
Level(+/-)
Speed Agree Detection
L4-04
Width(+/-)
Carrier Freq Reduction Off-
L8-40
Delay
STPo Detection Level (Low
L8-90
Speed)
n5-04 Speed Response Frequency
Initial Pole Detection
n8-35
Method
Pull-in Current @
n8-51
Acceleration
Frequency Display Unit
o1-03
Selection
o1-04 V/f Pattern Display Unit
*1 The setting range is 0.0 to 100.0 when A1-02 = 6 [PM Advanced Open Loop Vector].
*2 The setting range is 0.0 to 40.0 when A1-02 = 6 [PM Advanced Open Loop Vector].
*3 The default setting changes when the setting for C6-01 [Normal / Heavy Duty Selection] changes.
*4 This is the value for 200 V class drives. Double the value for 400 V class drives.
*5 The setting range is -100.0 to +100.0 when A1-02 = 6 [PM Advanced Open Loop Vector].
188
Range Unit
0.0 - 400.0 0.1 Hz
*4
0.0 - 255.0 0.1 V
0.0 - 2.0 0.1 s
0 - 4 1
*4
0 - 100 1 V
0 - 3 1
0.00 - 5.00 0.01
0.10 - 10.00 0.01
0.0 - 100.0 0.1
*1
0.0 - 400.0 0.1
*2
0.0 - 20.0 0.1
*5
-400.0 - +400.0 0.1
*2
0.0 - 20.0 0.1
0.00 - 2.00 0.01 s
0 - 5000 1
0.00 - 500.00 0.00 Hz
0 - 2 1
0 - 200% 1
0 - 3 1
0 - 1 1
YASKAWA TOEPYAIGA5001A GA500 DRIVE MAINTENANCE & TROUBLESHOOTING
Control Method (A1-02 Setting)
OLV/PM AOLV/PM
(5) (6)
Determined by E5-01 Determined by E5-01
- -
- 0.0
4 4
50 50
1 -
0.65 0.65
1.00 1.00
- -
0.0 Hz 0.0%
2.0 Hz 4.0%
0.0 Hz 0.0%
2.0 Hz 4.0%
0.00 0.00
0 80
- 20.00
0 1
50% 0
0 1
- 1
EZOLV
(8)
Determined by E5-01
-
-
Determined by E9-01
50
3
0.65
1.00
-
0.0%
4.0%
0.0%
4.0%
0.00
-
-
-
80%
1
-