YASKAWA GA500 Maintenance & Troubleshooting page 137

Setting Value Function
10B Torque Detection 1 (N.C.)
10C !Frequency Reference Loss
10D !Braking Resistor Fault
10E !Fault
110
!Alarm
111 !Fault Reset Command
Active
112 !Timer Output
113 !Speed Agree 2
114 !User-Set Speed Agree 2
115 !Frequency Detection 3
116 !Frequency Detection 4
117 Torque Detection 1 (N.O.)
118 Torque Detection 2 (N.C.)
119 Torque Detection 2 (N.O.)
11A !During Reverse
11B During Baseblock (N.O.)
11C !Motor 2 Selected
11E !Executing Auto-Restart
11F !Motor Overload Alarm
(oL1)
120 !Drive Overheat Pre-Alarm
(oH)
YASKAWA TOEPYAIGA5001A GA500 DRIVE MAINTENANCE & TROUBLESHOOTING
The terminal deactivates when the drive detects overtorque or undertorque.
OFF : The output current/torque exceeds the torque value set with L6-02 [Torque Detection Level 1], or the level has dropped and
remained in this state longer than the time set with L6-03 [Torque Detection Time 1].
The terminal deactivates when the drive detects a loss of frequency reference.
The terminal deactivates when the mounting-type braking resistor is overheating or when there is a braking transistor fault.
The terminal deactivates when the drive detects a fault.
Note:
Faults CPF00 and CPF01 [Control Circuit Error] are excluded.
The terminal deactivates when the drive detects a minor fault.
The terminal deactivates when the drive receives the Reset command from the control circuit terminal, serial communications, or
the communication option.
Sets the terminal as the timer output. Use this setting with the timer input set in H1-xx = 118 [MFDI Function Selection = !Timer
Function].
The terminal deactivates when the output frequency is in the range of the frequency reference ± L4-04 [Speed Agree Detection
Width(+/-)].
Note:
The detection function operates in the two motor rotation directions.
ON : The output frequency is not in the range of "frequency reference ± L4-04".
OFF : The output frequency is in the range of "frequency reference ± L4-04".
The terminal deactivates when the output frequency is in the range of L4-03 [Speed Agree Detection Level(+/-)] ± L4-04 [Speed
Agree Detection Width(+/-)] and in the range of the frequency reference ± L4-04.
Note:
The detection level set in L4-03 is a signed value. The drive will only detect in one direction.
ON : The output frequency is not in the range of "L4-03 ± L4-04" nor the range of frequency reference ± L4-04.
OFF : The output frequency is in the range of "L4-03 ± L4-04" and the range of frequency reference ± L4-04.
The terminal activates when the output frequency is higher than "L4-03 [Speed Agree Detection Level(+/-)] + L4-04 [Speed Agree
Detection Width(+/-)]". After the terminal deactivates, the terminal stays deactivated until the output frequency = L4-03.
Note:
The detection level set in L4-03 is a signed value. The drive will only detect in one direction.
ON : The output frequency is higher than L4-03 + L4-04.
OFF : The output frequency is less than L4-03 or is not more than L4-03 + L4-04.
The terminal deactivates when the output frequency is higher than the value of L4-03 [Speed Agree Detection Level(+/-)]. After the
terminal deactivates, the terminal stays deactivated until the output frequency = L4-03 - L4-04.
Note:
The detection level set in L4-03 is a signed value. The drive will only detect in one direction.
ON : The output frequency is less than "L4-03 - L4-04," or it is not more than L4-03.
OFF : The output frequency is more than L4-03.
The terminal activates when the drive detects overtorque or undertorque.
ON : The output current/torque exceeds the torque value set with L6-02 [Torque Detection Level 1], or the level has dropped and
remained in this state longer than the time set with L6-03 [Torque Detection Time 1].
The terminal deactivates when the drive detects overtorque or undertorque.
OFF : The output current/torque exceeds the torque value set with L6-05 [Torque Detection Level 2], or the level has dropped and
remained in this state longer than the time set with L6-06 [Torque Detection Time 2].
The terminal activates when the drive detects overtorque or undertorque.
ON : The output current/torque exceeds the torque value set with L6-05 [Torque Detection Level 2], or the level has dropped and
remained in this state longer than the time set with L6-06 [Torque Detection Time 2].
The terminal deactivates when the motor operates in the reverse direction.
ON : The motor is operating in the forward direction or the motor stopped.
OFF : The motor is operating in the reverse direction.
The terminal activates during baseblock. When the drive is in baseblock, the drive output transistor stops switching and does not
make DC bus voltage.
ON : During baseblock
OFF : The drive is not in baseblock.
The terminal deactivates when motor 2 is selected.
ON : Motor 1 Selection
OFF : Motor 2 Selection
The terminal deactivates when the Auto Restart function is trying to restart after a fault.
The terminal deactivates when the electronic thermal protection value of the motor overload protective function is a minimum of
90% of the detection level.
The terminal deactivates when the drive heatsink temperature is at the level set with L8-02 [Overheat Alarm Level].
3.10 H: Terminal Functions
Description
3
137