Roland SH-4d Owner's Manual page 174

PATTERN REVERB
Parameter Value
LF Damp G -36–0 [dB]
4000–12500 [Hz] (*6)
HF DampF
HF Damp -36–0 [dB]
G
GS Reverb
Parameter Value
ROOM1,
ROOM2,
ROOM3,
HALL1,
Char
HALL2,
PLATE,
DELAY,
PAN-DELAY
Pre LPF 0–7
Time 0–127
Feedback 0–127
SRV-2000
Parameter
R0.3, R1.0, R7.0, R15, R22, R26, R32, R37, H15, H22,
Selection
H26, H32, H37, P-B, P-A
0–160
PreDelay
Time 0.1–99.0 [sec]
HF Damp 0.05–1.00
Density 0–9
Attack 0–9
Gain
Attack 0–9
Time
ER Density 0–9
ER Level 0–99
Low Freq 0.04–1.00 [kHz]
Low Gain -24–+12 [dB]
Mid Freq 0.25–9.99 [kHz]
Mid Gain -24–+12 [dB]
0.2–9.0
Mid Q
HighFreq 0.80–9.99 [kHz]
HighGain -24–+12 [dB]
0.2–9.0
High Q
SRV-2000NL（NON-LINEAR）
Parameter Value
PreDelay 0–120
ReverbTime 0.9–+99.0 [sec]
GateTime 10–450
Low Freq 0.04–1.00 [kHz]
Low Gain -24–+12 [dB]
Mid Freq 0.25–9.99 [kHz]
Mid Gain -24–+12 [dB]
0.2–9.0
Mid Q
HighFreq 0.80–9.99 [kHz]
HighGain -24–+12 [dB]
174
Adjusts the LF damp attenuation amount (0: no effect).
Adjusts the frequency above which the high-frequency portion of the reverb sound is
cut.
Adjusts the HF damp attenuation amount (0: no effect).
This selects the reverb type.
Adjusts the amount of high-frequency attenuation for the sound fed into the reverb.
Adjusts the decay length of the reverb sound.
Adjusts the level at which the reverb sound is returned to the input.
Value
Adjusts the delay time from when the direct sound plays until the reverb sound is heard.
Adjusts the decay length of the reverb sound.
Adjusts the time it takes to cut off the reverb once the reverb begins to sound.
Sets the center frequency of the low range.
Adjusts the boost/cut of the low frequency range.
Sets the center frequency of the mid range.
Adjusts the amount of boost/cut of the mid-frequency range.
Sets the bandwidth of the mid-frequency range.
Higher values make the bandwidth narrower.
Sets the center frequency of the high range.
Adjusts the boost/cut of the high frequency range.
Explanation
Explanation
Explanation
Selects the type of reverb offered by the Roland SRV-2000
digital reverb.
Adjusts the delay time from when the direct sound plays until
the reverb sound is heard.
Adjusts the decay length of the reverb sound.
Adjusts the high-frequency portion of the reverb.
Adjusts the density of the late reverberation.
Adjusts the gain of the early reflections.
Adjusts the time of the early reflections.
Adjusts the density of the early reflections.
Adjusts the volume of the early reflections.
Sets the center frequency of the low range.
Adjusts the boost/cut of the low frequency range.
Sets the center frequency of the mid range.
Adjusts the amount of boost/cut of the mid-frequency range.
Sets the bandwidth of the mid-frequency range.
Higher values make the bandwidth narrower.
Sets the center frequency of the high range.
Adjusts the boost/cut of the high frequency range.
Sets the bandwidth of the high frequency range.
Higher values make the bandwidth narrower.
Explanation