Dispensing With The Autosteamer; Tips Regarding Its Use; Dispensing; Temperature Programming - Wega WBAR EVD Use And Maintenance Manual

WBAR

Dispensing with the Autosteamer

6.9
6.9.1

Tips regarding its use

• Only froth the amount of milk that you intend to use; once
heated, the milk will have to be completely poured out of
the jug and cannot be reheated.
• The steam wand only guarantees an accuracy of ± 3°C be-
tween the set temperature and the actual milk tempera-
ture, if the starting milk temperature is 4°C.
• As the steam automatically stops dispensing when the set
milk temperature is reached, only fill the jug half way in
order to prevent the milk froth from spilling out.
• Use a suitably-sized jug for the amount of milk that re-
quires frothing (approx. 200 ml is recommended) and
make sure that it is circular and not conical (see the image).
6.9.2

Dispensing

Do not direct the steam towards hands or other parts
of the body. Do not touch the steam nozzles with bare
hands; use the appropriate PPE.
• Immerse the steam wand nozzle tips (18) into milk;
18
button on the pushbutton panel (17);
• Press the
AUTO
STEAM
• wait until the dispensing process has been completed;
• to stop dispensing ahead of time, press the same
ton again.
Keep the tips clean at all times using a cloth dampened
in lukewarm water. Milk can be kept in the fridge for a
maximum of 3-4 days.
40 160
di
17
6.9.3

Temperature programming

The device leaves the factory with a default program-
ming of 60 ° C (± 2 ° C), for a quantity of 500ml of milk.
If you want to change this setting, proceed as follows:
• Immerse the steam nozzle in the milk to
be foamy, together with a thermometer
to control the temperature;
• press the
onds until the button flashes;
• press the Autosteamer
• Check with the thermometer the tem-
perature of the milk and, once reached
the desired one, lock the dispensing by pressing the Aut-
osteamer
• when the programming is complete press the
or wait 20 seconds.

Preset values

6.10
Use this procedure to reset the factory values both for the cof-
fee beverage doses.
Proceed as follows:
• Turn the machine off;
• switch the machine and press and hold down
the: ,
pushbutton panel;
• release the buttons only after having checked
that the LED
els is flashing;
• turn the machine OFF and ON.

Tips for a good cup of coffee

6.11
Wash the filters and filter holders on a daily basis, as indi-
cated in para. 7.5.2 on page 44. The failure to perform this
cleaning operation will negatively affect the quality of the dis-
pensed coffee.
7
To obtain high-quality coffee, it is important that the water
hardness does not exceed 6-7°f (French degrees). If the water
hardness exceeds these values, it is advisable to use a water
18 filter or softener. Avoid using a water softener if the water
hardness is less than 4°f.
If the taste of chlorine in the water is particularly strong, in-
stall a special filter.
Do not to keep large amounts of coffee beans on hand. If you
change the type of coffee, we recommend calling out the Tech-
nician to adjust the water temperature and coffee grinder.
If the machine has not been used for a certain period of time
but-
(2-3 hours), perform some cycles on empty. Make sure that
AUTO
STEAM
the machine is constantly cleaned and periodic maintenance
is carried out.
button for at least 5 sec-
STOP
PROG.
button;
AUTO
STEAM
button;
AUTO
STEAM
and buttons of the leftmost
STOP
PROG.
keys of both push-buttons pan-
STOP
PROG.
button,
STOP
PROG.
STOP AUTO
PROG. STEA
USER manual