Siruba LKS-1900AN Instruction Book page 9

2. 使用市場出售的離合馬達時，因被捲入 V
形皮帶而造成的事故，請一定選用安裝有
防止捲入功能的皮帶護罩的離合馬達。
⑷操作前
1. 為了防止人身事故，接通電源之前，請一
定確認連接器、電纜等確實沒有損傷、脫
落、鬆動。
2. 為了防止人身事故，請不要把手伸到活動
的部位。另外，請確認皮帶輪的轉動方向
是否與箭頭標記一致。
3. 使用帶腳輪的機台腳時，為了防止突然的
起動造成的事故，請一定鎖定腳輪，帶有
調節器時，請調節台腳把腳固定好。
⑸操作中
1. 為了防止捲入而造成的事故，操作機器
時，請注意不要讓手指、頭髮、衣服靠近
皮帶輪、手輪、馬達等轉動部位，也不要
把物品放到上面。
2. 為了防止人身事故，接通電源時或機器操
作中，請不要把手指靠近機針，也不要把
手指伸到挑線桿護罩裡。
3. 縫紉機以高速在進行轉動。為了防止弄傷
手，操作中絕對不能讓手靠近彎針、分線
器、針桿、旋梭、 布切刀等活動部位。另
外，更換縫紉機機線時，請關閉電源，確
認了縫紉機和馬達均完全停止之後再進行
更換。
4. 為了防止人身事故，從機台上拆卸縫紉機
時，或者返回安裝到原來的位置時，請注
意不要夾到手指。
2. If a commercially available clutch motor is
used with the machine, be sure to select
one with an entanglement preventive
pulley cover in order to protect against
being entangled by the V-belt.
⑷Before operation
1. Be sure to make sure that the connectors
and cables are free from damage, dropout
and looseness before turning the power
on in order to prevent accident resulting in
personal injury or death.
2. Never put your hand into the moving
sections of the machine in order to prevent
accident that can result in personal injury
or death. In addition, check to be sure
that the direction of rotation of the pulley
agrees with the arrow shown on pulley. 3.
If the table stand with casters is used, be
sure to secure the table stand by locking
the casters or with adjusters, if provided, in
order to protect against accident caused by
abrupt start of the machine.
⑸During operation
1. Be sure not to put your fingers, hair or
clothing close to the moving sections such
as the handwheel, hand pulley and motor
or place something near those sections
while the machine is in operation in order to
prevent accident caused by entanglement
that can result in personal injury or death.
2.Be sure not to place your fingers near the
surround area of the needle or inside the
thread take-up lever cover when turning
the power on or while the machine is in
operation in order to prevent accident that
can result in personal injury or death.
3. The machine runs at a high speed. Never
bring your hands near the moving sections
such as looper, spreader, needle bar, hook
and cloth trimming knife during operation in
order to protect your hands against injury.
In addition, be sure to turn the power off
and check to be sure that the machine
completely stops before changing the
thread.
4. Be careful not to allow your fingers or
any other parts of your body to be caught
between the machine and table when
removing the machine from or replacing
it on the table in order to prevent
accident that can result in personal injury
or death.
Introduction
ⅶ