Operation Of The Sewing Machine (Advanced) - Siruba LKS-1900AN Instruction Book

[ 6 ] 縫紉機的操作（應用篇）
1. 使用圖案鍵
縫製可以把已經登記的圖案（No.1 ～ 200）
登記到 P1 ～ P50 上。變更擴大縮小率、最
高轉速限制、線張力、 縫製位置就可以登
記，用圖案 No. 的滾動視窗選擇同樣可以登
記圖案，可以一次地叫出 P1 ～ P25。
※ 選擇了 P6 ～ P25 時，用下表所示的
按）進行縫製。
P-No. 選擇鍵 Selection key
P1 P1
P2 P2
P3 P3
P4 P4
P5 P5
P6 P1+P2
P7 P1+P3
⑴往圖案鍵上的登記
設定例 : 把圖案 No.3、X 擴大縮小 50％、
最高速度限制 2000sti/min、線張力"50＂、
圖案位置右移 0.5mm、前移 1mm 的設定登
記到 P2。
1）打開（ON）電源，按
（縫製 LED 應該滅燈）
進入方式設定（記憶體開關設定）。
1）Turn ON the power switch and press
to enter mode setting (memory switchsetting).
(Sewing LED should be put out.)
2）用
鍵、
2）Indicate the pattern register mode with
key.
3）按
鍵。進入圖案登記方式。
3）Press key.Enter the pattern register mode.
P29
進行
鍵的組合（同時
P-No. 選擇鍵 Selection key
P8 P1+P4
P9 P1+P5
P10 P2+P3
P11 P2+P4
P12 P2+P5
P13 P3+P4
P14 P3+P5
鍵。
鍵顯示出圖案登記模式。
[6] OPERATION OF THE SEWING
MACHINE (ADVANCED)
1. Performing sewing using the pattern keys
( , ,
Patterns (No.1 to 200) which have been
already registered can be registered to P1
to P50. It is possible to change and register
the scale, max. speed limitation, thread
tension and sewing position. Same as the
patterns (No.1 to 200), P1 to P50 are used
by the selection by scrolling the pattern No.
The pattern calling from P1 to P25 can be
made by one-touch as well.
※When selecting P6 to P25, perform the
selection by combination (simultaneous
pressing) of
keys as shown in the table below.
P-No. 選擇鍵 Selection key
P15 P4+P5
P16 P1+P2+P3
P17 P1+P2+P4
P18 P1+P2+P5
P19 P1+P3+P4
P20 P1+P3+P5
P21 P1+P4+P5
(1) Register to the pattern key
Setting example : Register following
setting to the P2., Pattern No. 3, X scale
rate : 50%, Y Scale rate :80%, Max. speed
limitation : 2,000 sti/min, Thread tension :
"50", Pattern position : 0.5 mm to the right
and 1 mm to the front.
key
or
, and )
, , , and
P-No. 選擇鍵 Selection key
P22 P2+P3+P4
P23 P2+P3+P5
P24 P2+P4+P5
P25 P3+P4+P5