Siruba LKS-1900AN Instruction Book page 11

3. 為了防止因突然的起動造成的事故，修理
和維修保養使用氣缸等高壓空氣的機器
時，請一定卸下空氣供給源的管子，排放
出殘留的空氣之後再進行修理和維修保
養。
4. 為了防止人身事故，修理調整和更換零部
件後，請一定確認螺絲螺母等沒有鬆動。
5. 機器的使用期間中，請一定定期地進行清
掃。此時，為了防止因突然的起動而造成
的事故，請一定關閉電源，確認了縫紉機
和馬達均完全停止之後再進行清掃。
6. 進行維修保養、檢查、修理時，請一定關
閉電源，確認了縫紉機和馬達均完全停止
之後再進行操作。( 離合馬達時，請注意
關閉電源後馬達由於慣性仍然回繼續轉動
一定時間。)
7. 為了防止人身事故，經過修理調整，機器
不能正常操作時，請立即停止操作，與本
公司或代理店聯繫，委託有關技術人員修
理。
8. 為了防止人身事故，保險絲熔斷後，請一
定切斷電源，排除了保險絲熔斷的原因之
後，更換相同規格的新保險絲。
9. 為了防止馬達的火災事故，請定期地進行
風扇通氣口的清掃和配線四周的檢查。
⑻使用環境
1. 為了防止因誤動作造成的事故，請在沒有
高頻電焊機等強噪音源 ( 電磁波 ) 影響的
環境下使用縫紉機。
3. When carrying out repair or maintenance
of the machine which uses air-driven
parts such as an air cylinder, be sure to
remove the air supply pipe to expel air
remaining in the machine before hand,
in order to prevent accident caused by
abrupt start of the air-driven parts.
4. Be sure to check that screws and
nuts are free from looseness after
completion of repair, adjustment and
part replacement.
5. Be sure to periodically clean up the
machine during its duration of use. Be
sure to turn the power off and verify that
the machine and motor stop completely
before cleaning the machine in order to
prevent accident caused by abrupt start
of the machine or motor.
6. Be sure to turn the power off and
verify that the machine and motor
stop completely before carrying out
maintenance, inspection or repair of the
machine. (For the machine with a clutch
motor, the motor will keep running for
a while by inertia even after turning the
power off. So, be careful.)
7. If the machine cannot be normally
operated after repair or adjustment,
immediately stop operation and contact
SIRUBA or the distributor in your area for
repair in order to prevent accident that
can result in personal injury or death.
8. If the fuse has blown, be sure to turn
the power off and eliminate the cause
of blowing of the fuse and replace the
blown fuse with a new one in order
to prevent accident that can result in
personal injury or death.
9. Be sure to periodically clean up the air
vent of the fan and inspect the area
around the wiring in order to prevent fire
accident of the motor.
⑻Operating environment
1. Be sure to use the machine under the
environment which is not affected by
strong noise source (electro-magnetic
waves) such as a high-frequency welder
in order to prevent accident caused by
malfunction of the machine.
Introduction
ⅸ