Siemens Simovert Masterdrives Compendium page 1513

Number / Alarm Cause
A178 - The program number for the main program
(level 0), which was transferred with block
Program number of search, is different from the selected program
block search forward number.
not allowed
- No breakpoint is known for the "automatic
block search" function (a program abort has
not yet occurred).
- A different program number is stored as the
breakpoint for the "automatic block search"
function.
Effect:
NC program execution is inhibited.
A179 The subprogram number specified with block
search for level 1 or level 2 does not exist.
Prog.No.of block srch
fwd level 1/2 does not Effect:
exist NC program execution is inhibited.
A180 The subprogram number transferred with
block search for level 1 is not the same as the
Prog.no. of block subprogram number in the NC block.
search forward level 1
<> cmd. Effect:
NC program execution is inhibited.
A181 The subprogram number transferred with
block search for level 2 is not the same as the
Prog.no. of block subprogram number in the NC block.
search forward level 2
<> cmd. Effect:
NC program execution is inhibited.
A183 The block number for the main program (level
0), which was transferred with block search,
Block no. of block does not exist in the main program.
search fwd l. 0 does
not exist Effect:
NC program execution is inhibited.
A184 The block number for the main program (level
0), which was transferred with block search,
Block no. of block does not contain a subprogram call for
search forward is no subprogram level 1.
UP call
Effect:
NC program execution is inhibited.
A185 The block number for subprogram level 1,
which was transferred with block search, does
Block no. of block not exist in the subprogram.
search forward does
not exist Effect:
NC program execution is inhibited.
A186 The block number for subprogram level 1,
which was transferred with block search, does
Block no of block not contain a subprogram call for subprogram
search fwd lev 1 is no level 2.
SP call
Effect:
NC program execution is inhibited.
A187 The block number for subprogram level 2,
which was transferred with block search, does
Block no of block not exist in the subprogram.
search fwd lev 2 does
not exist Effect:
NC program execution is inhibited.
26
Counter-measure
For the block search function, the selected
program number [PROG_NO] must be
specified as the program number for the main
program.
For the block search function, an existing
program number must be specified as the
subprogram number for level 1 or level 2.
For the block search function, the subprogram
number specified in the NC block must be
specified as the subprogram number for level
1.
For the block search function, the subprogram
number specified in the NC block must be
specified as the subprogram number for level
2.
For the block search function, an existing
block number must be specified as the block
number for the main program.
For the block search function, a block number
with a subprogram call must be specified as
the block number for the main program (level
0) if a block search is to be performed in
subprogram level 1.
For the block search function, a block number
which exists in this subprogram must be
specified as the block number for subprogram
level 1.
For the block search function, a block number
with a subprogram call must be specified as
the block number for subprogram level 1 if a
block search is to be performed in subprogram
level 2.
For the block search function, a block number
which exists in this subprogram must be
specified as the block number for subprogram
level 2.
6SE7087-6QX70 (Version AL)
Compendium Motion Control
03.2010
Siemens AG
SIMOVERT MASTERDRIVES