Buick LeSabre 1965 Service Manual page 321

SUPER TURBINE " 4 0 0 " DISASSEMBLY & ASSEMBLY 5 - 1 0 7
SECTION 5-D
TRANSMISSION DISASSEMBLY AND REASSEMBLY
CONTENTS OF SECTION 5-D
Paragraph Subject Page Paragraph
5-8 Disassembly of Major Units . . . . 5-107 5-22
5-9 Removal of Governor, Speedometer
Driven Gear, Pan, Strainer, and
Intake Pipe 5-108 5-23
5-10 Removal of Control Valve Assembly,
Governor Pipes and Detent
Spring Assembly 5-109 5-24
5-11 Removal of Rear Servo, Solenoid
Connector, Valve Body Spacer,
Gasket, Front Servo, Manual De- 5-25
tent and Park Linkage 5-109 5-26
5-12 Removal of Rear Oil Seal and 5-27
Extension Housing 5-112
5-13 Removal of Oil Pump 5-112 5-28
5-14 Disassembly of Gear Unit Assembly 5-115
5-15 Governor Assembly 5-116 5-29
5-16 Front Servo Disassembly, Inspection 5-30
and Reassembly 5-117
5-17 Rear Servo Disassembly, Inspection
and Reassembly 5-118 5-31
5-18 Control Valve Assembly Disassembly, 5-32
Inspection and Reassembly. . . . 5-119
5-19 Oil Pump Disassembly, Inspection 5-33
and Reassembly of Oil Pump . . 5-120
5-20 Forward Clutch Disassembly, In- 5-34
spection and Reassembly . . . . 5-125
5-21 Direct Clutch and Intermediate 5-35
Sprag Disassembly, Inspection 5-36
and Reassembly 5-128
Subject Page
Center Support and Intermediate
Clutch Disassembly, Inspection
and Reassembly 5-131
Inspection of Reaction Carrier, Rear
Sprag and Output Carrier
Assemblies 5-134
Pinion Replacement Procedure
Reaction and Output Carrier
Assemblies 5-134
Inspection of Output Shaft 5-134
Assembly of Rear Unit 5-137
Assembly of Units Into Trans-
mission Case 5-139
Rear Extension Housing
Assembly 5-142
Install Manual Linkage 5-143
Installation of Check Balls, Front
Servo, Gaskets, Spacer and
Solenoid 5-143
Installation of Rear Servo Assembly 5-144
Installation of Control Valve
Assembly and Governor Pipes . . 5-145
Installation of Strainer and Intake
Pipe
5
"
1 4 5
Installation of Modulator Valve
and Vacuum Modulator 5-145
Installation of Governor Assembly . 5-146
Installation of Speedometer Driven
Gear Assembly 5-146
5 - 8 DISASSEMBLY OF
MAJOR UNITS
1. With transmission in cradle on
portable jack, remove J-21366,
remove the converter assembly,
by pulling straight out.
NOTE: The convertor contains
a large amount of oil.
2. Install holding Fixture J-8763
on the transmission so that the
modulator assembly will be lo-
cated on the side of the holding
fixture that is nearest the bench.
3. Install fixture and transmis-
sion into holding Tool Base,
J-3289-20, with bottom pan facing
up. See Figure 5-500.
4. Remove modulator assembly
attaching screw and retainer. See
Figure 5-501.
5. Remove modulator assembly
and "O" ring seal from case. See
Figure 5-502.
J-3289-20
J-8763 v
Figure 5-500
Figure 5-501