Danfoss VLT AQUA Drive FC 200 Operating Instructions Manual page 78

How to Programme the Low Ha...
0-37 Display Text 1
Range: Function:
0 [0 - In this parameter it is possible to write an individual
*
0 ] text string for display in the LCP or to be read via
serial communication. If to be displayed permanently
select Display Text 1 in 0-20 Display Line 1.1 Small,
0-21 Display Line 1.2 Small, 0-22 Display Line 1.3 Small,
0-23 Display Line 2 Large or 0-24 Display Line 3 Large.
▲ ▼
Use the [ ] or [ ] buttons on the LCP to change a
character. Use the [
cursor. When a character is highlighted by the cursor,
it can be changed. Use the [
change a character. A character can be inserted by
placing the cursor between two characters and
▲ ▼
pressing [ ] or [ ].
0-38 Display Text 2
Range: Function:
0 [0 - In this parameter it is possible to write an individual
*
0 ] text string for display in the LCP or to be read via
serial communication. If to be displayed permanently
select Display Text 2 in 0-20 Display Line 1.1 Small,
0-21 Display Line 1.2 Small, 0-22 Display Line 1.3 Small,
0-23 Display Line 2 Large or 0-24 Display Line 3 Large.
▲ ▼
Use [ ] or [ ] on the LCP to change a character. Use
◀ ▶
[ ] and [ ] to move the cursor. When a character is
highlighted by the cursor, this character can be
changed. A character can be inserted by placing the
cursor between two characters and pressing [
▼
[ ].
0-39 Display Text 3
Range: Function:
0 [0 - In this parameter it is possible to write an individual
*
0 ] text string for display in the LCP or to be read via
serial communication. If to be displayed permanently
select Display Text 3 in 0-20 Display Line 1.1 Small,
0-21 Display Line 1.2 Small, 0-22 Display Line 1.3 Small,
0-23 Display Line 2 Large or 0-24 Display Line 3 Large.
▲ ▼
Use [ ] or [ ] on the LCP to change a character. Use
◀ ▶
[ ] and [ ] to move the cursor. When a character is
highlighted by the cursor, this character can be
changed. A character can be inserted by placing the
cursor between two characters and pressing [
▼
[ ].
0-70 Date and Time
Range:
Size related [ 0 - 0 ]
*
0-71 Date Format
Option: Function:
[0] YYYY-MM-DD Sets the date format to be used in the LCP.
*
VLT AQUA Low Harmonic Drive Operating Instructions
◀ ▶
] and [ ] buttons to move the
▲ ▼
] or [ ] on the LCP to
▲
] or
▲
] or
Function:
®
MG20T202 - VLT is a registered Danfoss trademark
0-71 Date Format
Option: Function:
[1] DD-MM-YYYY Sets the date format to be used in the LCP.
[2] MM/DD/YYYY Sets the date format to be used in the LCP.
0-72 Time Format
Option: Function:
Sets the time format to be used in the LCP.
[0] 24 h
[1] 12 h
*
0-74 DST/Summertime
Option: Function:
Choose how Daylight Saving Time/Summertime
should be handled. For manual DST/Summertime
enter the start date and end date in 0-76 DST/
Summertime Start and 0-77 DST/Summertime End.
[0] Off
*
[2] Manual
0-76 DST/Summertime Start
Range:
Size related [ 0 - 0 ]
*
0-77 DST/Summertime End
Range:
Size related [ 0 - 0 ]
*
6.3.2 1-0* General Settings
Define whether the frequency converter operates in open
loop or closed loop.
1-00 Configuration Mode
Option: Function:
[0] Open Motor speed is determined by applying a speed
*
Loop reference or by setting desired speed when in
Hand Mode.
Open Loop is also used if the frequency
converter is part of a closed loop control system
based on an external PID controller providing a
speed reference signal as output.
[3] Closed Motor Speed will be determined by a reference
Loop from the built-in PID controller varying the
motor speed as part of a closed loop control
process (e.g. constant pressure or flow). The PID
controller must be configured in parameter
group 20-** or via the Function Setups accessed
by pressing the [Quick Menus] button.
NOTE
This parameter cannot be changed while the motor is
running.
6
Function:
Function:
77
6