Related Manuals for AJA FS-HDR
Summary of Contents for AJA FS-HDR
- Page 1 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor Installation and Operation Guide Version 1.0r1 Published September 8, 2017...
-
Page 2: Notices
AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc. for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for use with recorder, router, software and camera products. Because it matters.™ is a trademark of AJA Video Systems, Inc. -
Page 3: Table Of Contents
Copyright ..........2 Contacting AJA Support ........2 Chapter 1 –... - Page 4 2 FS-HDR Mode ........
- Page 5 4 SNMP Enable Parameters....... 64 About FS-HDR Alarms ........64 5.1, 5.2 Power Supply 1-2 Alarm .
- Page 6 FS-HDR Mode ........
- Page 7 FS-HDR Tech Specs ........123...
-
Page 8: Chapter 1 - Introduction
The pursuit of High Dynamic Range (HDR) is the dream of getting closer to the Human Visual System (HVS) in all that we experience as viewers. FS-HDR has been designed to get us all there faster with a low profile, stand alone and real time device uniquely designed to bridge SDR to HDR, HDR to SDR and HDR to HDR, all in real time. -
Page 9: Video Features
• Embedded Audio (4x16 ch I/O in Four Channel Mode) • 277x208 routable mono audio matrix • Audio Sample Rate Conversion available on all audio inputs • Independent level, phase, delay controls for each audio channel FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 10: Other Features
Front Panel Control The FS-HDR front panel offers the most direct control, ideal for use in machine rooms or wherever quick changes and status checks must be made. The buttons and knobs control menus in the display, allowing you to fully configure the system according to your purposes. -
Page 11: Technical Description
The FS-HDR features an incredibly flexible architecture, offering powerful Video Processors for video conversion and processing, a separate Audio Processor, and input and output video and audio signal routing. The FS-HDR has two completely separate operating modes, selected with a menu parameter and then rebooting the unit. -
Page 12: Single Channel Mode
4K, UltraHD, 3G, HD, and SD video formats. The same processed output signal is sent to all the FS-HDR output connectors, depending on transport configuration. For example, when in Quad Link mode, the same signal is routed to the SDI Out 1-4 connectors, and also to the SDI Out 5-8 connectors (for use with optional SFP modules). -
Page 13: Video Processor(S)
The Video Processor also supports video signal adjustment with standard Proc Amp controls. The FS-HDR can embed 16 channels of audio from any of the audio inputs to each complete video output. On multiple link outputs, the audio is embedded on the first link. -
Page 14: Audio Processor
Optional FS-HDR Features SFP I/O All FS-HDR’s SFP I/O ports support up to 3G SDI data rates. In addition, in Single Channel mode the FS-HDR‘s SFP ports 5 through 8 In and Out also support 12G and 6G SDI, when equipped with a compatible SFP module. -
Page 15: Hdr And Wcg Background
The FS-HDR can be configured to operate with one of a variety of references, including genlock to the signal from the Reference input connector, genlock to the current video input signal, or Free Run. Your choice of reference needs to meet your individual facility requirements, and must be accounted for when you configure an FS-HDR video output format. -
Page 16: In This Manual
Appendix A: Specifications presents a list of technical specifications for the product. Appendix B: Pinouts explains the rear panel connector pinouts. Appendix C: Safety & Compliance provides regulatory compliance statements, advisories and warnings. Warranty and Index FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 17: Chapter 2 - Controls, Indicators, And Connections
(Selection LED Lights) Front Panel Layout and Operation The FS-HDR’s front panel control system is designed to be quick and easy to use. The alphanumeric display on the left shows status and parameter information. SELECT and ADJUST knobs provide fast menu scrolling, parameter selection and adjustment. -
Page 18: Operational Summary
Operational Summary To change FS-HDR operational parameters with the front panel controls: 1. Select a system component and menu group for the alphanumeric display: • For overall system control, press one of the six SYSTEM buttons, •... -
Page 19: Reset To Factory Default
• Pause on a parameter to select it for editing. For multiple fields in a parameter, use SELECT to move through the fields (after pressing ADJUST to enter field editing mode). • Push SELECT momentarily to undo and restore the previous setting. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 20: Button Menus
• Genlock reference source selection • Monitor output settings • Video input format settings, including 3G setup CONFIG Displays the Config Menu Group, which lets you configure the FS-HDR for your environment: • System Name setting • FS-HDR Mode (Single Channel or Four Channel) FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1... - Page 21 Off = No video is present, or invalid video is detected and the alarm is suppressed. NOTE: The FS-HDR operating mode can be determined by the VID 1-4 button tallies. In Four Channel Mode all four LEDs light, with the selected Video Processor high tally.
- Page 22 • Sidebar Edge • Matte adjustments TIMING • H and V timing and delay settings TSTGEN • Test Pattern settings FREEZE • Freeze Output setting Audio Menu Group Buttons LEVEL • Audio level and phase settings FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
-
Page 23: Status Led Indicators
• Red = A reference alarm condition exists (unless the alarm has been suppressed, in which case the LED will be turned off). Blinks blue on and off when you right-click on an FS-HDR system name and choose Identify in the web interface Network list. This action helps identify which system you’re controlling when multiple units are operated from a single... -
Page 24: Rear Panel Description
Example Reference and Video Incompatibility Alarms Video incompatibilities that the FS-HDR may detect include the following examples: Table 1. Video Incompatibility Examples Video Incompatibility Detected Alarm Status screen will show Video Status screen will show Genlock Source is set to “Reference”,... - Page 25 LAN through an Ethernet hub or switch. SFP In/Out (optional) All FS-HDR’s optional SFP I/O ports support up to 3G SDI operation. In addition, in Single Channel mode the FS-HDR‘s SFP ports 5 through 8 In and Out also support 12G and 6GSDI, when equipped with a compatible SFP module.
- Page 26 NOTE: For proper operation the input Reference signal must be stable and properly terminated using a 75-ohm terminator on either the unused loop connector or the last piece of downstream equipment to which the Ref Video is connected. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
-
Page 27: Chapter 3 - Installation & Configuration
Chapter 3 – Installation & Configuration Installation Overview The installation and set up of an FS-HDR is very simple. Plug both AC supply cords into AC mains power (separate branch circuits for redundancy), connect the LAN connector to a LAN, WAN or local computer with a web-browser, and then connect source and destination video and audio equipment. -
Page 28: Unpacking
You must remove any connected fiber or coaxial cables from the SFP modules before you remove the modules from the FS-HDR. Pull down the SFP lever to free the module before you withdraw the module from the cage. -
Page 29: Power Requirements
FS-HDR units. Note the location of cooling vents on all equipment next to the FS-HDR and ensure none are obstructed. NOTE: FS-HDR units can be stacked vertically without limit as long as there is an adequate supply of cool air around the FS-HDR side vents. -
Page 30: Networking Fs-Hdrhe 30 Using Your Own Static Ip
FS-HDR using a browser. Using Ping to Test the Network Connection If you have connected the FS-HDR to a computer and set up the IP address and still do not see the FS-HDR screens in your browser, you can ping the network to verify the connection. -
Page 31: Web Browser Control
To control the FS-HDR from a web browser on a network attached computer, enter the FS-HDR IP address as a URL in the browser. For example, if the FS-HDR IP address were “90.0.6.31”, you would then type into the web browser: http://90.0.6.31. -
Page 32: Software Update Installation
Mac or PC for upgrading your local FS-HDR machine. Unpack the Software FS-HDR software update files are “ZIP” files that you can open with a number of standard and third party file compression applications. The software image that you’ll install on the FS-HDR is a file with a name like FS-HDR_ver_1.0.0.0.bin or... -
Page 33: System Cabling
5. Click Restart FS-HDR with New Firmware to restart the FS-HDR. This will take the FS-HDR offline for a minute or two. During the restart, progress is shown in the connection area in the upper right corner of the FS-HDR Status screen. - Page 34 (w Embedded Audio) SDI In 7 SFP HD/SD (w Embedded Audio) Signal Z SDI In 8 SFP Video Processor 4 (w Embedded Audio) All incoming embedded audio is disembedded and sent to Audio Processor FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
- Page 35 Processor, so a total of two Dual Stream signals can be received for processing. Sixteen channels of embedded audio can be carried on each video signal, so up to 64 embedded audio channels can be routed to the FS-HDR Audio Processor. Figure 11. Four Channel Mode, Dual Stream Inputs Four Channel Mode BNC &...
-
Page 36: Single Channel Mode Configuration Examples
Dual Stream signals can be output. A Dual Stream signal carries two video images (SDI-A and SDI-B). The FS-HDR can also be configured to route only the Dual Stream SDI-A or SDI-B video image signal to an output connector. - Page 37 SDI In 3 BNC SDI In 4 BNC All incoming embedded audio is disembedded and SDI In 5 SFP sent to Audio Processor SDI In 6 SFP SDI In 7 SFP SDI In 8 SFP FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
- Page 38 Signal Z (w Embedded Audio) SDI Out 6 SFP Signal Z (w Embedded Audio) SDI Out 7 SFP Signal Z (w Embedded Audio) SDI Out 8 SFP Signal Z (w Embedded Audio) FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
-
Page 39: Local Monitoring With The Fs-Hdr
Dual Stream (SDI-A) Local Monitoring with the FS-HDR To support the widest range of monitoring devices, the FS-HDR provides an SDI and an HDMI monitor output. These outputs carry the same signal. In Single Channel mode, a 4K/UltraHD signal is automatically downconverted to 2K/HD on the monitor output. -
Page 40: Gpi Connections
Electrical isolation is provided for up to four pieces of external equipment. "GPI Pinouts" on page 128 for information on how to wire the GPI connector to work with external devices that you want to use to control the FS-HDR or that you want the FS-HDR to control. Stand Alone Tests The stand alone tests can be performed without a computer, using the FS-HDR front panel controls and rear connections. -
Page 41: Fs-Hdr Processing Examples
3. Connect a 1080i59.94 HD tri-level sync reference signal to one of the FS-HDR Ref Loop BNCs, and connect a 75 ohm terminator to the other Ref BNC. • The REF LED will light blue, indicating the FS-HDR is genlocked to reference. -
Page 42: General Fs-Hdr Setup
NOTE: The FS-HDR must restart after its operating mode has been changed. General FS-HDR Setup For any FS-HDR operation the following general menu items will need to be set correctly for your workflow. Some default FS-HDR settings may be applicable. -
Page 43: Hd Video Camera To Ultrahd Hdr Live Production
HD Video Camera to UltraHD HDR Live Production The following workflow demonstrates feeding an HD video camera signal to an UltraHD HDR capable video switcher through the FS-HDR for a live production. In this example a Canon camera's HD Log 2 output is converted to UltraHD Hybrid Log Gamma. -
Page 44: Hdr To Hd Hdr Down And Cross-Conversion
Procedure System Configuration 1. If the FS-HDR is not already in Single Channel Mode, press the CONFIG System button: • Select 2 FS-HDR Mode, select 4K/UHD and press the ADJUST knob. Wait for the FS-HDR to reboot (not longer than 90 seconds). - Page 45 HD tri-level sync signal to one of the Ref Loop BNC connectors, and terminate the other Ref Loop BNC connector. • Connect a Quad Link 4K 59.94 signal to the FS-HDR SDI 1, 2, 3, and 4 video input BNC connectors.
-
Page 46: Multiple Legacy Device Sdr To Hdr Live Conversion
SDI In 6 SFP converted signal SDI Out 6 SFP on each SFP output SDI In 7 SFP SDI Out 7 SFP (requires optional SFP modules) SDI Out 8 SFP SDI In 8 SFP FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... - Page 47 • Configure the source devices to the desired settings and connect them to SDI1 through SDI 4 BNC inputs on the rear of the FS-HDR. Once connected the LED below the VID1 button on the FS-HDR front panel will light.
-
Page 48: Multiple Simultaneous Hdr And Sdr Distribution
• View the FS-HDR SDI output signal on a compatible HDR display. Procedure System Configuration 1. If the FS-HDR is not already in Four Channel Mode, press the CONFIG System button: • Select 2 FS-HDR Mode, select HD/SD and press the ADJUST knob. Wait for the FS-HDR to reboot (not longer than 90 seconds). - Page 49 Standard (default), Soft 1-3, Bright VID3 FORMAT 1 Output Format 720p5994 VID3 FORMAT 2.1 Dynamic Range&Gamut Hybrid Log Gamma BT.2100 VID3 FORMAT 3.0 Link Cfg SDI3 Sngl Link LvlA VID3 FORMAT 4.0 Link Cfg SDI7 Sngl Link LvlA FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
- Page 50 HD tri-level sync signal to one of the Ref Loop BNC connectors, and terminate the other Ref Loop BNC connector. • Connect sources A and B to the FS-HDR SDI 1 and SDI 3 Input BNCs. • Install an optional SFP module into the FS-HDR SDI 5 Input cage and connect the source cable.
-
Page 51: Dual Stream Signal Separation
The following workflow demonstrates separating two Dual Stream inputs and routing the signals to different outputs. NOTE: In the following example, U, V, W, X, Y, and Z represent different complete signals, which may be carried on one or more connectors. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... - Page 52 Signal Y SDI Out 7 SFP (SDI-B only) (w Embedded Audio) Signal Z SDI Out 8 (w Embedded Audio) (SDI-A only) Table 6. FS-HDR Menu Settings for Figure System Button Menu Name Setting VIDEO 4.1 SDI1 3G Detect Dual Stream VIDEO 4.2 SDI2 Input Protect...
-
Page 53: Chapter 4 - Display Menus
Single Channel Mode. Menu parameters settings made in one mode may or may not affect the operation of FS-HDR when it is set to the other mode. For example, in Single Channel Mode, setting Output Image Mapping to 2SI will not affect operations in Four Channel Mode, because that parameter only affects 4K or UltraHD formats that are not available in Four Channel mode. -
Page 54: Presets And Fs-Hdr Operating Mode
Example: 1.0 ProcAmp is the parent menu of the 1.1 through 1.4 child menus. NOTE: In this chapter, menus unique to an FS-HDR operating mode will be indicated as (4Ch only) or (SingleCh only). Other menus are identical in both Four Channel and Single Channel modes. -
Page 55: Vid 1/2 I/O
NOTE: The STATUS menu always shows the FS-HDR’s current Ethernet settings. The parameters shown on the CONFIG Menu Group IP configuration menu may not display the values the unit is currently using. Vid 1/2 I/O (4Ch only) This menu shows the current primary video settings for Video Processors 1 and 2. -
Page 56: Vid Alarm
Fib Out Mode Fiber output mode. Power/Temp Alarm This menu shows the power supply status of the FS-HDR and the temperature status. If a power supply is unplugged, the display indicates PS OFF or PS Error. PS1 Alarm Status Displays the state of the PS1 power supply (OK or ERROR). -
Page 57: Caption Status
Caption Type & Presence REMOTE Menu Group The REMOTE Menu Group lets you set up how you want the FS-HDR to be controlled. Control options include the front panel, a remote computer running a browser, and GPI inputs and outputs. -
Page 58: Gpi In 1-4 Response
The setting of this parameter determines what happens when a GPI trigger is received at the FS-HDR’s GPI Inputs (1–4). A GPI Trigger is defined as a TTL low voltage level (0 to 0.8V with respect to its isolated ground pin). The GPI interface pinout and specifications are discussed in "GPI Pinouts"... -
Page 59: Interaction Of Presets And Gpis
GPI IN 1 Response setting of No Action. If you trigger GPI IN 1 later, expecting to recall Preset 1 again, the FS-HDR instead performs No Action. To prevent unexpected changes in the GPI IN Response parameters, set these parameters as desired before storing presets;... -
Page 60: Output Frame Rate
Reference (default) Use the signal on the Ref connector as the genlock source. Free run Free run mode (FS-HDR syncs to its own timebase, not locked to an Input external source) SDI<n> Use the selected SDI input signal as the genlock source. -
Page 61: Sdi1 3G Detect
2 physical input. Choosing Auto Detect or Dual Stream in SDI1 3G Detect does not switch away from the physical input. In the Dual Stream setting, the FS-HDR assumes both channels of Dual Stream 3G video are muxed onto a single wire at the SDI1 input. The SDI 2 video signal is then taken internally from the SDI 1 Stream B signal instead of the SDI2 In connector. -
Page 62: 4.6, 4.8 Sdi4/6/8 Input Protect
SNMP, alarm, and screen saver configurations. 1 System Name This parameter defines a unique name for the FS-HDR. This same name is used both when displaying systems via the web interface and when displaying the FS-HDR’s screen saver. -
Page 63: Fs-Hdr Mode
DHCP (default) Select automatic IP address assignment from the LAN DHCP server. If the FS-HDR cannot find a DHCP server, it fails over to the static IP address. Static Addr Assign a static IP address manually (using the following parameter menus). -
Page 64: Subnet Mask
Without a properly configured default gateway (whether you have a router/ gateway or not), the FS-HDR will be unable to see other FS units on the network, although you may still be able to control this unit via a web browser. Also, without a proper gateway defined, the discovery feature on the Network web page will fail to list other FS units on the network. -
Page 65: 5.2 Power Supply 1-2 Alarm
Reference video signal. When set to NORMAL, the alarm triggers (the REF LED on the FS-HDR front panel will light red) if the Reference signal is not detected or is incompatible with the processor format. -
Page 66: Display Intensity
At 25C (77F) ambient temperature any speed setting (1 to 10) provides adequate cooling. At 40C (104F) ambient, a fan speed of 5 or higher is recommended. The FS-HDR also has built-in thermal protection that will increase the fan speed automatically if necessary. -
Page 67: 2.8 Sdi 1-8 Src Mode
In Auto mode, normal PCM audio passes through the Sample Rate Converters and gets converted, as appropriate. If any of the active signal pairs are non-PCM the SRC is turned off for all audio inputs. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 68: Mix Down 1 Mode
NOTE: The LFE channel is not used in the stereo mix down output, but is passed through the FS-HDR audio routing matrix. The Mix Down outputs are available as inputs to the FS-HDR audio matrix and can be mapped to any audio output. -
Page 69: Mix Down 2 Mode
Rear Rear Multi-channel audio, typically embedded in an SDI signal, can be passed through the FS-HDR converter unchanged. The multi-channel sound can also be mixed down to stereo, using the two Mix Down Modules built into the FSI-X Audio Processor. -
Page 70: Mix Down Reset
Resets the Mix Down 2 mixer levels to default settings. 8 Global Audio Output This parameter allows routing the same source or set of sources to all the FS-HDR audio outputs. The rules used for Audio Out apply if the number of outputs do not match the number of inputs. -
Page 71: Factory Preset
During recall, the display reads, Recalling until the recall is finished. On recall completion, the displays shows the success or failure: Recalled, Failed, or Empty. A failed or empty recall does not recall anything and leaves the FS-HDR as it was. (Preset registers are empty until you store something in them.) During a store, the display reads Storing until the store is finished. -
Page 72: Video Select Buttons Vid1-Vid4
Link as the Video Input will allocate all four SDI Inputs for Quad Link use. The SFP inputs operate the same way. "System Cabling" on page 33 for more information about FS-HDR signal routing. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 73: Dynamic Range&Gamut
3:2 pull down field removal is enabled for interlaced video sources. About Reverse Telecine and Film Cadence Film cadence is a way to convert film frame rates to interlaced field rate video suitable for broadcast, commonly employed by telecine equipment when FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 74: Input Scan Format
FS-HDR Reverse Telecine Conditions The FS-HDR converter can perform film cadence removal under the following conditions: • Input signal must be 525i59.94, 1080i59.94 and output format selected must be p23.98 or PsF23.98, OR the input signal must be 1080i60 and output format... -
Page 75: Anc Menu Group
Auto If there is no AFD code on the input video, a “Full Frame” (8) code is inserted. If the FS-HDR is converting, the appropriate AFD code will be chosen based on the convert mode (see "7 Upconvert Mode" on page 82 "8 Downconvert Mode"... -
Page 76: Downconvert Afd Dflt
Off (default) When Off, caption translation is not performed. When set to On, the FS-HDR will automatically translate incoming line 21 captions to CEA-708 format and insert the VANC packets into the converted video stream. This is a complete translation from CEA-608 format to CEA-708 format (including the embedded SD captions). -
Page 77: Color Menu Group
These parameters allow adjustment of signal levels to meet legal broadcast requirements. When set to Off, the Video Legalizer is not enabled, and the following clip controls are not active. In YUV mode, the White Clip, Black Clip, FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... - Page 78 (18 Caption Xlator must be Off). Pass In Pass mode, the FS-HDR does not blank line 21 of the SD video input and passes the unaltered video to the Video Processor for transformation. This is the setting to use if there is no captioning data present on line 21 of a 525i video input.
-
Page 79: Format Menu Group
HDR and SDR modes on that monitor (which may go black during the change- over). The FS-HDR default setting is No Clamp, and this generally should be used during production. When set to 100 Nits, the HDR signal is cleanly compressed to SDR, allowing quick A/B comparison on an HDR display in HDR mode. -
Page 80: Link Config Sdi1, 2, 3, 4
Select both the Vid3 and Vid4 Processor signals for output (Dual Stream). Figure 30. Dual Stream 3G MUX Schematic HD/SD Video Processor 1 HD/SD Video Processor 2 Figure 14 on page 36 for more information. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 81: Link Config Sdi1-4
SD source input. This parameter has an effect only when the input and output are both SD (525i or 625i). Off (default) No ARC conversion will be performed. Letterbox Selects the indicated ARC conversion. H Crop Pillarbox V Crop 14x9 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 82: Upconvert Mode
Using a combination of zoom and stretch, the image is sized to fit a 16x9 screen (this can introduce a small aspect ratio change). NOTE: Any Custom Size/Pos values (only available in Four Channel Mode) will be applied on top of this settings. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 83: Downconvert Mode
NOTE: Any Custom Size/Pos values (only available in Four Channel Mode) will be applied on top of this settings. NOTE: Any Custom Size/Pos values (only available in Four Channel Mode) will be applied on top of this settings EXCEPT when Downconvert Mode is set to Auto AFD. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 84: Scale Menu Group
Because Auto AFD mode fully defines the size, position, and aspect ratio of the output raster, any Custom Size/Pos settings and any Region Of Interest settings are ignored, and those menus are hidden. FS-HDR AFD processing (passing, removing, and re-inserting) occurs based on the setting of parameter "1.1 AFD Out"... -
Page 85: Custom Size/Pos
Enables changing the vertical position. 1.5 Custom Left Crop This parameter changes the Left picture crop position. 100% (default) Maintains the normal left side position of the selected format. +10.0% to +100.0% Enables changing the left side position. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 86: Region Of Interest (Roi)
(AFD) is in control of the Conversion Mode. • Custom Size and Position settings work interactively with ROI, but Custom Crop settings are disabled. Custom Size/Pos is also temporarily disabled while in the ROI Setup mode. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 87: Keyer Menu Group
The underlying hardware feature is the same as Custom Right Crop and Custom Left Crop. This is effectively an extra handle on the Left Crop and Right Crop parameters. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 88: Matte Luma
0 to the width of the line in pixels. The maximum value varies, depending on the format already chosen. Variable Adjustment range increments from 0 to the width of the line in pixels. The maximum varies, depending on the format chosen. Default: 0 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 89: Output Timing V
2639 -562 1080psf29.97, 1080psf30 2199 -562 2Kx1080p23.98, 2Kx1080p24 2749 -562 2Kx1080p25 2639 -562 2Kx1080p29.97, 2Kx1080p30 2199 -562 2Kx1080p50 2639 -562 2Kx1080p59.94, 2Kx1080p60 2199 -562 525i59.94, 525psf29.97 -262 625i50, 625psf25 -312 720p23.98, 720p24 4124 -375 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 90: Frame Delay
Default: 0 NOTE: This delay amount is in addition to the FS-HDR’s default video latency. In Four Channel Mode and in Single Channel Mode with no Ultra-HD/4K up or down conversion, this default latency is nominally two frames at low frame rates (23.98/24/25/29.97/30 fps) or four frames at high frame rates (50/59.94/60 fps). -
Page 91: Freeze Output
1 Freeze Output This parameter tells the FS-HDR to freeze the current video frame on the Video Processor output. This may be useful either for testing or in case of loss of the input source. Off (default) Normal video is output (no freeze). - Page 92 10.0 - 16.0 SDI2-8 Phase Same as 9.0 SDI1 Phase menu, except for SDI inputs 2 through 8, and similar phase adjust submenus are available. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
-
Page 93: Aes/Madi Menus
This parameter selects the Audio Delay Mode for the eight SDI1 audio input channel pairs. Delay operates on channel pairs only. Delay cannot be adjusted on any single channel. Channel pairs are grouped as: Channel 1 and 2, Channel FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 94: Aes/Madi Delay Menus
When AES is selected, Delay parameter menus for AES and MADI input audio are displayed. These menus are the similar to those used for Embedded Audio SDI1 Delay. 1.0 AES Delay Sixteen AES Level menus (and related submenus) are available. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 95: Map Menu Group
(EMBED or AES/MADI). These settings are NOT shared with both Four Channel and Single Channel modes. The MAP menus provide FS-HDR audio routing controls. Any audio input can be routed to any audio output, except the Monitor output embedded audio always matches the monitored video. -
Page 96: 4.0 Sdi2-4 Audio Out
-Mix Down 1 R -Mix Down 2 L (4Ch only) -Mix Down 2 R (4Ch only) -Sig Gen 1kHz -Sig Gen 400Hz -Mute 2.0-4.0 SDI2-4 Audio Out "1.0 Vid 1 Audio Out" on page 95 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 97: Chapter 5 - Browser Remote Control
IP address in the STATUS Menu Group as follows: 1. Press the STATUS button on the FS-HDR front panel. 2. Turn the SELECT knob until you reach status display with the FS-HDR name at the top. 3. Enter the IP address shown in the IP Addr field. - Page 98 FS-HDR models on the network- below the line will be a list of other AJA devices (such as Cion and other FS models) If you right-click any system in the list and select Identify, the ID LEDs on the unit will blink to identify it.
-
Page 99: Controllifs-Hdrg Multiple 99S
From any screen, you can see at-a-glance all of the AJA devices present on the same local LAN as well as the current FS-HDR you are controlling. Clicking on any of the listed systems will bring up the Status screen of that device. -
Page 100: Sub-Menus
Screen Descriptions Now that you have had an introduction to how the FS-HDR browser works and how to navigate the screens, each screen and its settings are described in detail (click to jump). -
Page 101: Ip Address Type
Apply button. DHCP (default) Select automatic IP address assignment from the LAN DHCP server. If the FS-HDR cannot find a DHCP server, it fails over to the static IP address. Static Addr Assign a static IP address manually. The factory default static IP address: 192.168.0.2... -
Page 102: Alarm Configuration Screen
Without a properly configured default gateway (whether you have a router/ gateway or not), the FS-HDR will be unable to see other AJA FS devices on the network, although you may still be able to control this FS-HDR via a web browser. -
Page 103: Status Screen
Figure 36. Status Screen Top, Four Channel Mode Figure 37. Status Screen Bottom, Four Channel Mode The Status screen displays overall FS-HDR operational status. You can right-click most video values to change them, allowing you to edit many parameters in one place. - Page 104 Right-clicking on the Global Audio Out parameter value lets you select a global output. That same audio will be sent to all the FS-HDR audio outputs. When set to Off, the other Audio Outputs display their selected value, otherwise only the Global Audio Output setting is displayed.
-
Page 105: Config Screen
FS-HDR Mode Selects whether the FS-HDR will operate in Four Channel or Single Channel mode. A confirm dialog displays a warning that a reboot of the FS-HDR system will occur. HD/SD After reboot the FS-HDR will operate in Four Channel (HD/SD) mode. -
Page 106: Hidden Menus
UPnP Proxy enables the FS-HDR to serve as a proxy for other AJA devices, allowing them to be discovered on a Windows network through the FS-HDR. When enabled, the FS-HDR acts as a proxy for all the AJA devices that it is able to FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1... -
Page 107: Video Screen
The devices will be listed in the FS-HDR Network window. Once the devices appear on the network, they can connect directly to other devices and computers without involving the FS-HDR. -
Page 108: Audio Screen
Audio Screen The Audio screen controls the FS-HDR’s system wide audio signal processing. The parameters available on the Audio browser screen are essentially identical to the front panel display menus. The only difference is parameters are set using webpage controls (drop down menus, slider adjustments) instead of control knobs. -
Page 109: Presets Screen
Storing and recalling a Preset will affect all the settings for all four channels in that mode. Care must be taken to establish a policy for the use of FS-HDR Presets, especially if the FS-HDR is operated in Four Channel mode and the different channels have different users. -
Page 110: Interaction Of Presets And Gpis
Store The Store buttons let you save the current FS-HDR configuration into the preset register with the associated name and number. A preset is a set of all System, Video, Audio, and Output parameters as they were set at the time the preset was stored. -
Page 111: Remote Screen
The Update Firmware screen allows you to download and install a firmware update from AJA. The FS-HDR Update Page link on the Firmware screen will take you to the correct AJA website page. Or you can visit the AJA website (aja.com) to locate and download the updated software. -
Page 112: Video Channel Screens
Video Channel Screens The Video Channel screens control the FS-HDR’s video signal processing of that channel (either four or one, depending on mode). In Four Channel Mode four menu groups are selected on the left. In Single Channel Mode only one menu group is available. -
Page 113: Format Screen
Complete descriptions of the parameters on this screen are accessible using the following cross references: • "1 Output Timing H" on page 88 • "2 Output Timing V" on page 89 • "3 Frame Delay" on page 90 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 114: Scale Screen
"1 Background Fill" on page 87 • "2 Sidebar Edge" on page 87 • "3.1 Matte Luma" on page 88 • "3.2 Matte Chroma" on page 88 • "3.3 Matte Hue" on page 88 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 115: Test Gen Screen
"1.0 Proc Amp Enable (YUV)" on page 77 • "3.0 Video Legalizer" on page 77 ANC Screen Complete descriptions of the parameters on this screen are accessible using the following cross references: • "1.1 AFD Out" on page 75 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 116: Freeze Screen
SDI output channel. Embed Level Screen Complete descriptions of the parameters on this screen are accessible using the following cross references: • "EMBED Level Menus" on page 91 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 117: Embed Delay Screen
"2.0-4.0 SDI2-4 Audio Out" on page 96 AES (and MADI) Audio Channel Screens The AES Audio Channel browser screens display Level, Delay, and Mapping controls for the AES, MADI BNC and MADI Fiber audio channels. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 118: Aes/Madi Level Screen
The parameters on this screen are similar to those for the Embedded Audio Channel screens, except they apply to either AES or MADI audio inputs. For more information see: • "EMBED Delay Menus" on page 93 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 119: Aes/Madi Map Screen
The parameters on this screen are similar to those for the Embedded Audio Channel screens, except they apply to either AES or MADI audio inputs. For more information see: • "1.0 Vid 1 Audio Out" on page 95 • "2.0-4.0 SDI2-4 Audio Out" on page 96 FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 120: Chapter 6 - Snmp
FS-HDR. Besides activating SNMP, trap destinations must also be defined with fixed IP addresses. When SNMP is enabled, one or more of these alarms may be sent by the FS-HDR to the client network management system (NMS) as a trap message: •... -
Page 121: Front Panel Snmp Configuration
Front Panel SNMP Configuration FS-HDR SNMP configuration can be accomplished using the front panel or with the web browser computer interface (if Remote Control is enabled). The FS-HDR front panel screens for SNMP are accessible through the CONFIG button. The direct SNMP configuration screens are: •... -
Page 122: Snmp Configuration Parameters
Disabled (default) When set to Disabled, the FS-HDR will not issue SNMP trap messages. Enable 1 When set to Enable 1, the FS-HDR issues SNMP trap messages to Trap Destination 1 (parameter 4.1) and as defined in the MIB. Enable Both When set to Enable Both, the FS-HDR issues SNMP trap messages to Trap Destination 1 and 2 (parameters 4.1 and 4.3) and as defined in... -
Page 123: Appendix A - Specifications
• (HD) 1920 x 1080PsF 23.98, 24, 25, 29.97, 30 • (HD) 1920 x 1080i 50, 59.94, 60 • (HD) 1280 x 720p 50, 59.94, 60 • (SD) 625i 50 • (SD) 525i 59.94 • YCbCr, 4:2:2, 10-bit FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... -
Page 124: Video Output Digital
• 1 x HDMI, 1 x HD output • 2K/HD/SD, HDMI v1.4a • Monitored Video Processor output (video and audio) is simultaneously output on both connectors • 4K/UltraHD down-converted to 2K/HD • Crop control on HDMI output FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... - Page 125 • SD Pillarbox: Produces an image in the center of the screen with black borders on the left and right sides and an anamorphized image in the center • V Crop: Transforms SD letterbox material to an anamorphic image FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
-
Page 126: Network Interface
• Lock to SDI input 1 thru 8 • Free run based on Temperature Compensated Crystal Oscillator Network Interface • 1 x RJ-45, 10/100/1000 Ethernet • Embedded web server for remote control • SNMP FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com... - Page 127 • Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F) • Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140 degrees F) • Operating Relative Humidity: 10-90% noncondensing • Operating Altitude: <3,000 meters (<10,000 feet) FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...
-
Page 128: Appendix B - Fs-Hdr Pinouts
Ground The GPI inputs and outputs are electrically isolated from power and ground on the FS-HDR frame. There are four inputs and four outputs. Electrical isolation is provided for up to four pieces of external equipment. The following guidelines apply to the four GPI inputs and outputs: •... -
Page 129: Audio Connection Pinouts
The pinout scheme above is used for the AES/EBU digital audio connections. Each channel handles a pair of digital audio signals (16 total per connector). The top connector is for digital audio input channels 1-16, and the bottom connector is for digital audio output channels 1-16. FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 www.aja.com...