GE B30 Communications Manual page 449

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
InjAmp MV Injected current.
SH INJECTION AMPS in amperes.
InjVol MV Injected voltage.
INJECTED VOLTAGE in volts.
SH INJECTION VOLTS in volts.
InService SPS LED indication - Relay In-service. The LED IN SERVICE operand.
IntermSt1 SPS Intermediate-status detected.
The BREAKER/SWITCH INTERM operand.
IntrAlm SPS Indicates that the current exceeded the maximum interrupting current rating
during the last interruption event.
The BKR ARC 1 MAX OP operand.
IntrAlmDpo SPS Inverse of IntrAlm.
The BKR ARC 1 MAX DPO operand.
IrigbFail SPS A bad IRIG-B input signal has been detected.
The IRIG-B FAILURE operand.
IsoBlk ACT B90 - Indicates that the isolator position is invalid
IsOn SPS Indicates the time of day timer is on.
The TIME OF DAY 1 ON operand.
IsoPos ACT B90 - Indicates position of isolator. When "On", the related current is included in
differential zone; when "Off", the current is excluded from differential calculations.
LastClrTm INS Represents the UTC time of user fault reports last cleared time in seconds elapsed
since 1970/01/01, 00.00.00.
The LAST CLEARED DATE actual value.
LastRptTm INS Represents the UTC time of last user fault report generated time in seconds
elapsed since 1970/01/01, 00.00.00.
The LAST REPORT DATE actual value.
LastSqNum INS Last sequence number received.
Actual value RxGOOSE1 SqNum.
LatchErr SPS A difference is detected between the wanted and actual latch contact state.
The LATCHING OUT ERROR operand.
LeoSt SPS Line end open status.
The LINE PICKUP LEO PKP operand.
LivDea SPS This data object indicates that live/dead conditions have been met.
The SYNC 1 DEAD S OP operand, which indicates that live/dead conditions have
been met.
LivDeaDpo SPS This data object indicates that live/dead conditions have not been met.
The SYNC 1 DEAD S DPO operand, which indicates that live/dead conditions have
not been met.
LivLiv SPS This data object indicates that both sources are live, and that angle, frequency,
and voltage difference and range conditions have been met.
The SYNC 1 SYNC OP operand, which indicates that both sources are live, and that
angle, frequency, and voltage difference and range conditions have been met.
LivLivDpo SPS This data object indicates that one or both sources are not live, or that angle,
frequency, and voltage difference and range conditions have been met.
The SYNC 1 SYNC DPO operand, which indicates that one or both sources are not
live, or that angle, frequency, and voltage difference and range conditions have
been met.
LivV1 SPS This data object indicates that V1 is above the LivVal1 setting.
The SYNC 1 V1 ABOVE MIN operand, which indicates that V1 is above the LivVal1
setting.
LoadDev MV Indicates the motor load standard deviation at the time of the broken rotor bar
data acquisition stage.
LOAD DEV. AT BRB CALC. in x FLA.
LocCmdAcsOff SPS Indicates operations of FlexLogic operand ACCESS LOC CMND OFF
LocCmdAcsOn SPS Indicates operations of FlexLogic operand ACCESS LOC CMND ON
LocMod SPS Capacitor control in local mode.
The CAP 1 IN LOCAL operand.
UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical nodes...
SubHaPHIZ
FldGnd0PHIZ, SubHaPHIZ
LEDsIHMI
BkrΘXCBR, DiscΘXSWI,
GGIO3
CBArc0SCBR
CBArc0SCBR
LPHD
B_IsoSSWI
TmDayGAPC
B_IsoSSWI
UFlt0RFLO
UFlt0RFLO
LGOS
LPHD
LinPkpPIOC
SynChkRSYN
SynChkRSYN
SynChkRSYN
SynChkRSYN
SynChkRSYN
BknRotSVBR
SecGSAL
SecGSAL
CapCtlGAPC
3-211
3