GE B30 Communications Manual page 447

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
DynArmd SPS This data object indicates that dynamic mode is armed.
The SYNC1 S-CLOSE ARMD operand, which becomes On when dynamic mode is
armed.
DynDpo SPS The SYNC1 S-CLOSE DPO operand, which becomes Off when all criteria for
dynamic mode are fulfilled
DynOp SPS This data object indicates that all criteria for dynamic mode are fulfilled if value is
TRUE else false.
The SYNC1 S-CLOSE OP operand, which becomes On when all criteria for dynamic
mode are fulfilled.
Ena1 SPS Function is Enabled.
The AR ENABLED operand.
EqLim SPS The number of pulses counted is equal to the set number.
Counter 1(CNT1) EQL operand, which indicates the number of pulses counted is
equal to the set number.
EqpMismat SPS The configuration of modules does not match the stored order code.
The EQUIPMENT MISMATCH operand.
EvtEna1 ENG Setting to enable generation of events in event record, 0 = Disabled, 1 = Enabled
EvtLED SPS An LED - Event Cause LED status. For graphical front panel.
The EVENT CAUSE LED 1 operand.
EvtRcdClr SPC Clear Event Records (erase all Events).
The CLEAR EVENT RECORDS command.
Fail SPS Ground Protection Module Failure.
GPM-F (Field Ground Protection Module) Fail status.
The GPM-F FAILURE operand.
FDLOp SPS Overcurrent fault detector low has operated.
The 87PC FDL OP operand.
FlexErrTkn SPS A FlexLogic equation is incorrect.
The FLEXLOGIC ERR TOKEN operand.
Flt3Ph SPS Fault indication - Three phase fault.
The PHASE SELECT 3P operand.
FltAB SPS Fault indication - Phase A to B.
The PHASE SELECT AB operand.
FltABG SPS Fault indication - Phase A to B to ground.
The PHASE SELECT ABG operand.
FltAG SPS Fault indication - Phase A to ground.
The PHASE SELECT AG operand.
FltBC SPS Fault indication - Phase B to C.
The PHASE SELECT BC operand.
FltBCG SPS Fault indication - Phase B to C to ground.
The PHASE SELECT BCG operand.
FltBG SPS Fault indication - Phase B to ground.
The PHASE SELECT BG operand.
FltCA SPS Fault indication - Phase C to A.
The PHASE SELECT CA operand.
FltCAG SPS Fault indication - Phase C to A to ground.
The PHASE SELECT CAG operand.
FltCG SPS Fault indication - Phase C to ground.
The PHASE SELECT CG operand.
FltCntClr SPC TRUE = clear incipient fault count. The clear incipient fault counters command.
FltCntPhφ INS Number of detected incipient faults.
INCIPIENT FAULT 1 PH A/B/C FAULTS.
FltLinID VSS Faulted line ID
FltLocation MV Fault location in percentage.
The FAULT LOCATION in percentage of field winding from negative terminal in
case of single point injection. If double point injection, displays Invalid value.
FltLoopReact MV D30, D60, L60, L90 - The fault loop reactance
UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical nodes...
SynChkRSYN
SynChkRSYN
SynChkRSYN
Rec13pRREC, Rec3pRREC
DigCntFCNT
LPHD
GGIO3
LEDsIHMI
Master/LLN0
FldGnd0PHIZ
PhCmp1PDIF
LPHD
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
ICFltPTEF
ICFltPTEF
FltRFLO
FldGnd0PHIZ
FltRFLO
3-209
3