GE B30 Communications Manual page 448

MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Data object CDC
name
FltLoopRis MV
FltMulti SPS
FltRis MV
FltSegment ENS
FltSLG SPS
FltVoid SPS
FrcTrigger SPC
3
FrstEthFail SPS
Function1 ENG
FwdOp SPS
GoDatSetRef ORG
GoEnaPort1 ENG
GoID VSG
GndAmp MV
GndNeutInd SPS
GndRis MV
GpsFail1 SPS
GrAct1 SPS
GrdMasterID VSS
Ha3NV MV
Ha3ZroV MV
HiZIOC ACT
HiZSt ENS
HzChgRte MV
HzLedInd SPS
HzObAccum MV
IdFail1 SPS
IndFailBeh ENG
IndPos1 DPS
3-210
Semantics
D30, D60, L60, L90 - The fault loop resistance
Fault indication - Multi phase fault.
The PHASE SELECT MULTI-P operand.
L90 - The fault resistance at the fault point
L90 - Indicates in which segment of the line the fault occurred: 0 = N/A, 1 = LOCAL,
2 = REMOTE 1, 3 = REMOTE 2
Fault indication - single line to ground.
The PHASE SELECT SLG operand.
Fault indication - Fault type not detected.
The PHASE SELECT VOID operand.
Command for the Hi-Z Oscillography Force Trigger
First Ethernet failure.
The FIRST ETHERNET FAIL operand.
Function Enable/Disable setting: 0 = Disabled, 1 = Enabled (note that TISSUE 670
suggests something like this named SetMod)
Fault direction is forward.
The NEG SEQ DIR OC1 FWD operand.
The NTRL DIR OC1 FWD operand.
Expected value of datSet field in messages subscribed to by RxGOOSE#
The setting RxGOOSE1 DatSet.
Enable all GOOSE on Ethernet port setting: 0 = Disabled, 1 = Enabled
Expected value of goID field in messages subscribed to by RxGOOSE#
The setting RxGOOSE1 ID.
Ground current.
The FIELD GROUND CURRENT in amperes.
An LED.
The LED NEUTRAL/GROUND operand.
Ground resistance.
FIELD GROUND RESIST in ohms.
STATOR GND. RESIST in kilo ohms.
GPS failed at terminal corresponding to instance number.
The 87L DIFF GPS 1 FAIL operand.
Setting group corresponding to index is active (not instantiated in C30).
The SETTING GROUP ACT 1 operand.
Grand master ID actual value
Third harmonic component of neutral voltage.
STATOR GND 3RD HARM VN in volts.
Third harmonic component of zero sequence voltage.
STATOR GND 3RD HARM V0 in volts.
Indicates phase instantaneous overcurrent has operated
Represents the status of Hi-Z fault detection function
Frequency rate of change measured value.
FREQUENCY RATE OF CHANGE 1 in Hz/s.
An LED.
The LED FREQUENCY operand.
FREQUENCY OOB BAND 1 ACCUMULATION in percentage (%)
ID check for a peer L30/L90 on the channel has failed.
87L DIFF CH 1 ID FAIL operand, which becomes On when the differential element's
ID check for a peer L30 on channel 1 has failed.
Setting to select the behavior of the RxGOOSE Boolean when the sending device is
offline: 0 = On, 1 = Off, 2 = Latest/On, 3 = Latest/Off
Generic remote DPS input status values: 0 for intermediate-state, 1 for off, 2 for
on, 3 for bad-state.
RxGOOSE DPS1 actual value.
CHAPTER 3: IEC 61850 COMMUNICATION
Used in logical nodes...
FltRFLO
PhSelGAPC
FltRFLO
FltRFLO
PhSelGAPC
PhSelGAPC
HiZPHIZ
LPHD
Master/LLN0
NegDocRDIR, NeuDocRDIR
LGOS
Master/LLN0
LGOS
FldGnd0PHIZ
LEDsIHMI
FldGnd0PHIZ, SubHaPHIZ
LinDfPDIF
Master/LLN0
TmClkLTMS
StatrPHIZ
StatrPHIZ
HiZPHIZ
HiZPHIZ
RteHzPFRC
LEDsIHMI
HzBnd$PTUF
LinDfPDIF
GGIO3
GGIO3
UR FAMILY – COMMUNICATIONS GUIDE