Danfoss VLT FC 100 Operating Instructions Manual page 85

5 How to Operate the Frequency Converter
The number of the Active Set-up (selected as the Active Set-up in
Active Set-up ) is shown. When programming in another Set-
par. 0-10
up than the Active Set-up, the number of the Set-up being program-
med appears to the right in brackets.
The Middle section (b) shows up to 5 variables with related unit, re-
gardless of status. In case of alarm/warning, the warning is shown in-
stead of the variables.
The Bottom section (c) always shows the state of the frequency
converter in Status mode.
It is possible to toggle between three status read-out displays by press-
ing the [Status] key.
5
Operating variables with different formatting are shown in each status
screen - see below.
Several values or measurements can be linked to each of the displayed
operating variables. The values / measurements to be displayed can be
Display Line 1.1 Small , par. 0-21 Display Line 1.2
defined via par. 0-20
Small , par. 0-22 Display Line 1.3 Small , par. 0-23 Display Line 2 Large
Display Line 3 Large , which can be accessed via [QUICK
and par. 0-24
MENU], "Q3 Function Setups", "Q3-1 General Settings", "Q3-13 Display
Settings".
Each value/measurement readout parameter selected in par. 0-20
play Line 1.1 Small to par. 0-24 Display Line 3 Large has its own scale
and number of digits after a possible decimal point. Larger numeric val-
ues are displayed with few digits after the decimal point.
Ex.: Current readout
5.25 A; 15.2 A 105 A.
Status display I:
This read-out state is standard after start-up or initialisation.
Use [INFO] to obtain information about the value/measurement linked
to the displayed operating variables (1.1, 1.2, 1.3, 2, and 3).
See the operating variables shown in the display in this illustration. 1.1,
1.2 and 1.3 are shown in small size. 2 and 3 are shown in medium size.
Status
799 RPM
1.1
1.2
Auto Remote Ramping
2
Status display II:
See the operating variables (1.1, 1.2, 1.3, and 2) shown in the display
in this illustration.
84
1 (1)
7.83 A 36.4 kw
0.000
53.2 %
3 1.3
MG.11.F3.02 - VLT
VLT HVAC Drive High Power Operating In-
In the example, Speed, Motor current, Motor power and Frequency are
selected as variables in the first and second lines.
1.1, 1.2 and 1.3 are shown in small size. 2 is shown in large size.
Status
1.1
Auto Remote Running
Status display III:
This state displays the event and action of the Smart Logic Control. For
further information, see par. .
Status
778 RPM
State: 0 o 0 (o )
When: -
Dis-
Do: -
Auto Remote Running
Display Contrast Adjustment
▲
Press [status] and [ ] for darker display
▼
Press [status] and [ ] for brighter display
Status
Top section
43 RPM
Middle section
! Pwr.card temp (W29)
Bottom section
Auto Remote Running
Indicator lights (LEDs):
If certain threshold values are exceeded, the alarm and/or warning LED
lights up. A status and alarm text appear on the control panel.
The On LED is activated when the frequency converter receives power
from mains voltage, a DC bus terminal, or an external 24V supply. At
the same time, the back light is on.
• Green LED/On: Control section is working.
® is a registered Danfoss trademark
1 (1)
207RPM 5.25A 24.4 kW
6.9
Hz
2
1 (1)
0.86 A 4.0 kW
!
5.44 A 25.3kW
1.4 Hz
2.9%
structions
1.3
1.2
1(1)