Omron 3G3RX User Manual page 202

4-2 Function Mode
The functions switchable via the SET/SET3 terminal are:
F002/F202/F302 *
F003/F203/F303 *
A003/A203/A303
A004/A204/A304
A020/A220/A320 *
A041/A241
A042/A242/A342 *
A043/A243/A343 *
A044/A244/A344
A046/A246 *
A047/A247 *
4
A061/A261 *
A062/A262 *
A092/A292/A392 *
A093/A293/A393 *
A094/A294
A095/A295
A096/A296
b012/b212/b312 *
b013/b213/b313 *
H002/H202
H003/H203
H004/H204
H005/H205 *
H006/H206/H306 *
H020/H220
H021/H221
H022/H222
H023/H223
H024/H224
H030/H230
H031/H231
H032/H232
H033/H233
H034/H234
H050/H250 *
H051/H251 *
H052/H252 *
H060/H260 *
*: Parameters changeable during operation.
• The 1st/2nd/3rd control functions are displayed identically. You'll see which one is enabled by checking whether
the terminal is turned on/off.
• When both SET and SET3 terminals are turned on, priority is given to SET, and the 2nd control function is
enabled.
• During operation, you cannot switch between the 1st, 2nd, and 3rd control functions. You can switch them only
during stop.
4-83
: 1st/2nd/3rd acceleration time
: 1st/2nd/3rd deceleration time
: 1st/2nd/3rd base frequency
: 1st/2nd/3rd maximum frequency
: 1st/2nd/3rd multi-step speed reference 0
: 1st/2nd torque boost selection
: 1st/2nd/3rd manual torque boost voltage
: 1st/2nd/3rd manual torque boost frequency
: 1st/2nd/3rd V/f characteristics selection
: 1st/2nd automatic torque boost
voltage compensation gain
: 1st/2nd automatic torque boost slip
compensation gain
: 1st/2nd frequency upper limit
: 1st/2nd frequency lower limit
: 1st/2nd/3rd acceleration time 2
: 1st/2nd/3rd deceleration time 2
: 1st/2nd 2-step acceleration/deceleration
selection
: 1st/2nd 2-step acceleration frequency
: 1st/2nd 2-step deceleration frequency
: 1st/2nd/3rd electronic thermal level
: 1st/2nd/3rd electronic thermal characteristics
selection
: 1st/2nd motor parameter selection
: 1st/2nd motor capacity selection
: 1st/2nd motor pole number selection
: 1st/2nd speed response
: 1st/2nd/3rd stabilization parameter
: 1st/2nd motor parameter R1
: 1st/2nd motor parameter R2
: 1st/2nd motor parameter L
: 1st/2nd motor parameter I0
: 1st/2nd motor parameter J
: 1st/2nd motor parameter R1 (auto-tuning)
: 1st/2nd motor parameter R2 (auto-tuning)
: 1st/2nd motor parameter L (auto-tuning)
: 1st/2nd motor parameter I0 (auto-tuning)
: 1st/2nd motor parameter J (auto-tuning)
: 1st/2nd PI proportional gain
: 1st/2nd PI integral gain
: 1st/2nd P proportional gain
: 1st/2nd Limit at 0 Hz
U/T1
V/T2
W/T3
SET
SET3
P24
Motor 1
Motor 2
Motor 3