Error Codes - Canon i-SENSYS MF229dw Service Manual

Error Codes

Code Detection description
When the same error repeatedly occurs after several
times of turning the power OFF/ON, execute the following
remedies.
(1) Check that the heater resistance measured between
1PIN and 2PIN of the cable (J101) on the DC Controller
Board is in the following range. Replace the Fixing
Fixing Assembly does Assembly when the resistance value is abnormal.
E000 0000 not start up within [1] 120 V machine - Heater resistance: 16.0 Ω ±7%
specified time. [2] 230 V machines - Heater resistance: 53.8 Ω ±7%
(2) Check the connection of connector (J101) on the DC
Controller Board.
(3) Check the connection of connector (J552) on DC
Controller Board.
(4) Replace the Fixing Assembly.
(5) Replace the DC Controller Board.
When the same error repeatedly occurs after several
times of turning the power OFF/ON, execute the following
remedies.
(1) Check that the heater resistance measured between
1PIN and 2PIN of the cable (J101) on the DC Controller
Board is in the following range. Replace the Fixing
Assembly when the resistance value is abnormal.
Abnormal high-
E001 0000 [1] 120 V machine - Heater resistance: 16.0 Ω ±7%
temperature detection
[2] 230 V machines - Heater resistance: 53.8 Ω ±7%
(2) Check the connection of connector (J101) on the DC
Controller Board.
(3) Check the connection of connector (J552) on DC
Controller Board.
(4) Replace the Fixing Assembly.
(5) Replace the DC Controller Board.
When the same error repeatedly occurs after several
times of turning the power OFF/ON, execute the following
remedies.
(1) Check that the heater resistance measured between
1PIN and 2PIN of the cable (J101) on the DC Controller
Board is in the following range. Replace the Fixing
Assembly when the resistance value is abnormal.
Abnormal low-
E003 0000 [1] 120 V machine - Heater resistance: 16.0 Ω ±7%
temperature detection
[2] 230 V machines - Heater resistance: 53.8 Ω ±7%
(2) Check the connection of connector (J101) on the DC
Controller Board.
(3) Check the connection of connector (J552) on DC
Controller Board.
(4) Replace the Fixing Assembly.
(5) Replace the DC Controller Board.
7
Error Codes > Error Codes
Remedy
7 Error Codes > Error Codes
Code Detection description
When the same error repeatedly occurs after several
times of turning the power OFF/ON, execute the following
Fixing power supply
E004 0000 remedies.
drive circuit error
(1) Replace the DC Controller Board.
(2) Replace the Fixing Assembly.
When the same error repeatedly occurs after several
Error detection on any
times of turning the power OFF/ON, execute the following
of scanner motor, laser
E100 0001 remedies.
unit, and BD detection
(1) Replace the Laser Scanner Unit.
at scanner area.
(2) Replace the DC Controller Board.
ROM read/write error When the same error repeatedly occurs after several
(Error in storing each times of turning the power OFF/ON, execute the following
E196 2000 setting values for user remedies.
mode / service mode / (1) Update the set of the Controller Firmware
factory mode) (2) Replace the Main Controller Board.
When the same error repeatedly occurs after several
times of turning the power OFF/ON, execute the following
remedies.
(1) Check the connection of Flat Cable between Main
Contact Sensor HP
E202 0002 Controller Board (J5) and Contact Sensor.
error, Failure in return
(2) Replace the Flat Cable between Main Controller Board
(J5) and Contact Sensor.
(3) Replace the Contact Sensor.
(4) Replace the Main Controller Board.
When the same error repeatedly occurs after several
times of turning the power OFF/ON, execute the following
remedies.
Light intensity of a lamp (1) Check the connection of Flat Cable between Main
E225 0001 is less or equal to the Controller Board (J5) and Contact Sensor.
criteria (2) Replace the Flat Cable between Main Controller Board
(J5) and Contact Sensor.
(3) Replace the Contact Sensor.
(4) Replace the Main Controller Board.
When the same error repeatedly occurs after several
times of turning the power OFF/ON, execute the following
remedies.
(1) Check the connection of Flat Cable between Main
Insufficient light intensity
E301 0001 Controller Board (J5) and Contact Sensor.
in shading
(2) Replace the Flat Cable between Main Controller Board
(J5) and Contact Sensor.
(3) Replace the Contact Sensor.
(4) Replace the Main Controller Board.
7-3
Remedy
7-3