Table of Contents
Advertisement
EXT.
(PPM signal at DSC sock-
et)
If your transmitter is fitted with a non-Graupner exter-
nal RF module connected to the DSC / Data socket,
you can switch between the standard internal HoTT
RF module and the external module when you switch
model memories in the "Module" line by choosing
either "HoTT", "EXT.", or "SP.", as described in the fol-
lowing section.
You can now use the arrow button of the right-hand
four-way button to move to the first Value field in the
"Module" line before pressing the central
of the right-hand four-way button:
B A S I C
S E T T I N G , M O D E L
Model name
Graubele
Info
1234g/111111
Stick mode
HoTT
bind bind
Module
SEL
BD1 BD2 BD3 BD4
In the active Value field you should now use the Se-
lect buttons to choose "EXT." or – if appropriate – the
"SP." mode (described below) instead of "HoTT".
When you select "EXT.", the HoTT-specific value fields
are replaced by the modulation type already selected
in the "DSC output" line; see page 89:
B A S I C
S E T T I N G , M O D E L
Model name
Graubele
Info
1234g/111111
Stick mode
EXT. PPM
Module
SEL
96
Program description - Base setup models | Helicopter models
The lines of the "Receiver output" and "Range test"
options (described below) are also suppressed, as
are all the HoTT-specific displays in the base display;
"PPM" is also superimposed instead of "HoTT":
Graubele
#01
0:00h
PPM
H-J Sandbrunner
00:00h
4.1V
0
SET
button
SP mode
If you need for external RF module from another
manufacturer, or however, instead of the analog PPM
signal a special digital signal, then connect it to the
DATA jack and select the line "module" to "SP Mode":
1
B A S I C
n/a
n/a
Model name
Info
Stick mode
Module
SP mode
SEL
Also include here the choice by pressing the central
SET
key of the right or the centre
touch pad.
Parallel to this choice are also the options described
below "Receiver output" and "Range Test" and hidden
all HoTT-specific displays in the basic display and
instead of "HoTT", "SP" is displayed:
1
PPM10
0:00.0
Stop watch
0:00.0
Flight time
K78
V
RX VOLT:0.0v
M
0
0
0
(Digital signal at DSC socket)
S E T T I N G , M O D E L
Graubele
1234g/111111
1
1
bind
MOD
BD
ESC
key of the left
Graubele
Stop watch
#01
0:00h
SP
Flight time
H-J Sandbrunner
00:00h
K78
4.1V
V
M
0
0
0
"Mode" column
B A S I C
S E T T I N G , M O D E L
Model name
Graubele
Info
1234g/111111
Stick mode
1
Module
SP mode
SEL
MOD
In this column you select the transmission mode of
the external RF module:
•
Mode "1":
2-channel hopping
•
Mode "2":
x-channel hopping
"BIND" column
B A S I C
S E T T I N G , M O D E L
Model name
Graubele
Info
1234g/111111
Stick mode
1
Module
SP mode
SEL
MOD
The "BIND" column in the right-hand column can be
used to initiate the "Bind" process of the non-Graup-
ner system – the transmitter's RF section must be
switched off when the transmitter is first switched
on.
0:00.0
0:00.0
RX VOLT:0.0v
0
1
bind
BD
1
bind
BD
Advertisement
Table of Contents
