GENE R AL BAS IC S ET T IN G S
Pre-set DSC Output
Pre-set Pitch min.
Top LCD contrast
Bottom LCD contrast
Now display contrast can be adjusted in the value
fi eld displayed in inverse video within a range of ±20
by using the selection keys of the right touch pad.
GE NE RAL BAS IC S ET T IN G S
Pre-set DSC Output
Pre-set Pitch min.
Top LCD contrast
Bottom LCD contrast
GENE R AL BAS IC S ET T IN G S
Pre-set DSC Output
Pre-set Pitch min.
Top LCD contrast
Bottom LCD contrast
Simultaneously tapping the or selection keys
of the right touch pad (CLEAR) will reset the inverse
video fi eld back to "0".
Display light
This line determines how long the transmitter dis-
play's backlight illumination is to remain on after
switching the transmitter on or after the last activation
of a transmitter operating element.
Available options are "unlim(ited)", "30 s", "60 s",
"120 s" and "off".
A simultaneous tap on the or selection keys
of the right touch pad (CLEAR) will reset the inverse
PPM10
video fi eld to "unlimited".
rear
Power on/off beep
0
A power on/off beep for the transmitter can be
0
switched on ("yes") and off ("no") in this line.
SEL
A simultaneous tap on the or selection keys
of the right touch pad (CLEAR) will switch this option
shown in inverse video back to "yes".
Battery type
G E N E R A L B A S IC S ET T I N G S
PPM10
Bottom LCD contrast
rear
Display light
0
Power-on/off beep
-15
Battery type
SEL
This line specifi es whether transmitter power is pro-
vided by a four-cell NiMH battery or a single-cell LiPo
PPM10
battery. As a consequence of this setting, the next
rear
line will offer a suitable voltage range for the "Battery
0
warning" threshold.
+15
A simultaneous tap on the or selection keys
of the right touch pad (CLEAR) will switch this option
SEL
shown in inverse video back to "Lith.".
Battery warning threshold
G E N E R A L B A S IC SE T TI N G S
Display light
Power-on/off beep
Battery type
Battery warning
You can arbitrarily specify the warning threshold for
the display ...
... – contingent on the battery type selection in the
line above – in increments of 0.01 volt between 4.50
and 5.50 V (NimH battery) or 3.40 and 4.20 V (LiIo/
LiPo battery). Make sure that you do not enter a value
which is too low, so that you still have suffi cient time
to safely land your model in the event of a battery
warning.
0
A simultaneous tap on the or selection keys
unlim.
of the right touch pad (CLEAR) will switch the fi eld
shown in inverse video back to its factory setting,
yes
4.70 V (NiMh) or 3.60 V (Lith.).
Li-Io
SEL
Power-on warning
G EN ER AL BASI C SET TI N G S
Power-on/off beep
Battery type
Battery warning
Stick warning
In this line you can determine how long the transmit-
ter should wait after the last actuation of an operating
element until the activation of an optical and acoustic
power-on warning before the transmitter switches off
unlim.
automatically one minute later.
yes
The values "unlim(ited)", "30 s" and 1, 5, 10, 20, 30
and 60 minutes are optional selections.
Li-Io
A simultaneous tap on the or selection keys
3.60V
of the right touch pad (CLEAR) will reset the inverse
SEL
video fi eld to "unlimited".
Program description - Basic settings
Batt. must
be re-
charged!!
yes
Li-Io
3.60V
unlim
SEL
279