Table of Contents
Advertisement
Note:
To restart the transmitter after an automatic
shut-off, first push the transmitter's power
switch to the right into its "OFF" position then,
after about five seconds, again into its "ON" position
(toward the antenna).
Touch Sense
G ENE RAL BA SIC SET T IN G S
Battery type
Battery warning
Stick warning
Touch Sense
In this line you can select the touch sensitivity of the
touch pads in a range from 1 to 10. The lower this
number is, the more sensitive the touch pad will be to
taps and vice versa.
A simultaneous tap on the or selection keys
of the right touch pad (CLEAR) will reset the field
shown in inverse video back to "2".
DATA sel
Firmware version V1102 and higher
From firmware version V1102 it can be connected
to the Data socket not only a Smart-Box or alterna-
tively an external RF module, but also the external
Bluetooth module of MZ transmitter, No. 8351 can be
operated. The data protocol consequently required in
each case on the "Data jack" can be selected in the
"DATA SEL." line:
280 Program description - Basic settings
G E N E R A L B A S IC S ET T IN G S
Battery warning
Stick warning
Touch Sense
DATA sel
"Telemetry"
The signal data protocol at the data socket corre-
Li-Io
sponds to the previous protocol and is suitable for
3.60V
connecting an external RF module and the data out-
unlim
put on the Smart-Box under the menu "EXTERNAL
2
MONITOR".
SEL
"Bluetooth"
The signal at the data socket Data Protocol is to
meet the needs of the external Bluetooth module, No.
8351, matched and thus particularly for the transmis-
sion of telemetry data and any language editions on
the suitable "Graupner HoTT Viewer App for Android"
compatible smartphones and / or tablets.
The output via "Bluetooth" mode data can be
authenticated in a rudimentary when needed
using the Smart Box and the option "MODEL
SELECT".
Note for Smart-Box:
The menus under the heading "SETTING
AND DATA VIEW" complement HoTT trans-
mitter of the first generation to the functions
of the same menu item in today's HoTT transmitter
telemetry menu, see section "Set view" on page 238.
Completely regardless of directly connected to the
Smart Box sensors it can be adjusted at any time and
displayed with the help of these menu items.
When a receiver is directly connected, however, the
display of the Smart box remains empty.
Own phase name 1 ... 10
3.60V
G EN ER AL BASI C SET TI N G S
unlim
Stick warning
2
Touch sense
Telemetry
Region
SEL
Own phase name
Up to ten phase names can be freely specified for
one's own use. Each of these can be up to 7 charac-
ters long. The characters of the name are assembled
by selecting them from a list. In addition to the stand-
ard names, these additional names will then also be
available in all model memory locations.
If possible, new phase name entries should begin
with the "Own phase name 1" line.
Change to the character table with a brief tap on the
centre
SET
key of the right touch pad:
!"#$%&'()
@ACDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
`abcdefghijklmnopqrstuvwxyz{|}~
¢ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÖÜ
Own phase name
Now the desired characters can be selected with the
selection keys of the left touch pad. With a brief tap
on the selection key of the right touch pad or its
SET
centre
key, move to the next position in which a
character can be selected. A simultaneous tap on the
or keys of the right touch pad (CLEAR) will
place a space character at the current position.
Positioning to any character position within the entry
field can be done with the keys of the right touch
pad.
unlim
2
EURO
1
+,–./0123456789:;
?
A
Advertisement
Table of Contents
