GRAUPNER MC-32 Manual page 265

Programming
Use the selection keys on the left or right touch pad
to scroll to the menu option »Multichannel« menu
option in the multi-function menu:
MIX active/phase MIX-only channel
Dual mixer Fail-safe adjust
Teacher / pupil Tx. output swap
Profi trim Trim memor y
Telemetr y Channel sequence
Multichannel Ring limiter
MIX-only channel Dual mixer
Swashplate mixer Fail-safe adjust
Teacher / pupil Tx. output swap
Profi trim Trim memor y
Telemetr y Channel sequence
Multichannel Ring limiter
... then open this menu option with a brief tap on the
centre SET key of the right touch pad.
Here, in the second column from the left, each of the
two multi-channel functions can be activated ("ACT")
or deactivated ("INACT") as desired and in the third
column the given function can be assigned to one of
the transmitter channels, C5 through C8, in a list.
M U L T I C H A N N E L
MULTIC1 INACT C5 MULTIC 4CH
MULTIC2 INACT C6 MULTIC 4CH
SET SEL
Note:
When a changeover is made to the »Servo
display« or if »Servo adjustment« is
used to select the "-travel+" or "-lim +"
columns for these previously set channels, their
respective cells will flash to indicate that these
channels have been activated in the
»Multichannel« menu. The preset values of 100 %
or 150 % should not be changed.
Prior to channel selection, please observe the
following notices:
1. Switch to the "SETTINGS/DISPLAYS" line of the
»Telemetry« menu and tap on the centre
of the right touch pad:
• on the "RX SERVO" page, select the "20 ms"
setting in the last line "PERIOD", see page 248.
• On the "RX SERVO TEST" display page, select
the "SAME" option for the last line "CH OUT
TYPE", see page 254.
2. The control channel used may not be used as an
input nor as an output channel for any mixer! For
example, if C5 is selected, be sure that the "Aile/
flaps" line of the »Model type« menu (page 105)
is preset to "1AIL" or that the "Swashplate type"
line of the »Helicopter type« menu (page 112) is
preset to "1 servo".
3. The channel settings intended for NAUTIC control
channel purposes in the »Control adjust« (page
108 ... 122) and »Servo adjustment« (page
112) menus are to be left as they are or reset
back to their original settings. Do not assign any
transmitter control or switch to the respective input
either. Also be sure that the servo's direction of
rotation is not reversed. Leave the servo middle at

SEL
0 %.
M U L T I C H A N N E L
MULTIC1 ACT
MULTIC2 ACT
SET
In the next column to the right, make a separate
channel count specification for each of the two multi-
channels; "MULTIC 4C." for the NAUTIC-Multi-Prop
mini decoder, No. 4142.N or "MULTIC 8C." for the
NAUTIC-Expert switching module, No. 4159.
SET key
M U L T I C H A N N E L
MULTIC1 ACT
MULTIC2 ACT
SET
Afterward, use the right arrow symbol at the bottom
line's right end to switch over to the second page of
settings for the »Multichannel« menu:
M U L T I C H
Input 1 fr –––
Input 2 fr –––
fr –––
Input 3
Input 4 fr –––
fr
Input 5 –––
Input 6 fr –––
Input 7 fr –––
Input 8 fr –––
SEL
This menu page is now used for making individual
settings for "MULTICH 1" and "MULTICH 2".
Program description - Multichannel
C5 MULTIC 4CH
C6 MULTIC 4CH

SEL SEL
C5 MULTIC 4CH
C6 MULTIC 8CH

SEL SEL
2
0% +100% +100%
0% +100% +100%
0% +100% +100%
0% +100% +100%
0% +100% +100%
0% +100% +100%
0% +100% +100%
0% +100% +100%
Offset – travel +
265