GRAUPNER MC-32 Manual page 119

I5 GL fr --- 0% +100%
I6 GL fr --- 0% +100%
I7 GL fr --- 0% +100%
EI GL fr --- 0% +100%
Normal
TYP SEL Offset – travel +
• "GL(obal)"
The settings for the input in question affect all
flight phases programmed (if any) and thus act
"globally" on the model memory in question.
• "PH(ase)"
The settings for this input take effect per
flight phase and must therefore be configured
separately for each flight phase.
Notes:
See page 152 for more information about
flight phases.
Column 3, "Transmitter control/switch
assignment"
Select an input, 5 through 16, with the  selection
keys of the left or right touch pad.
Transmitter control assignment
Use the selection keys to move into the column la-
beled SEL. After completing the activation of transmit-
ter control assignment by tapping the centre
of the right touch pad, the message shown below will
appear in the display:
+100% 0.0 0.0 I5 GL fr
+100% 0.0 0.0 I6 GL fr
+100% 0.0 0.0 I7 GL fr
+100% 0.0 0.0 I8 GL fr
Normal
–time+ TYP SEL
Now actuate the desired transmitter control: The no-
tice window will disappear and the designation of the
selected transmitter control will appear in the trans-
mitter control assignment window.
I5 GL S11 ---
I6 GL fr
fr
I7 GL
EI GL fr
Normal
TYP SEL
Alternatively, the centre
pad can be tapped for a second time while the notice
window, see above, is still on the display:
I5 GL fr
I6 GL fr
I7 GL fr
EI GL fr
SET
key
Normal
TYP SEL
--- 0% +100% +100% 0.0 0.0
--- Move desired 0% +100% +100% 0.0 0.0
--- control adj. 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
Offset – travel + –time+
0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
---
0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
Offset – travel + –time+
SET key of the right touch
--- 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
Offset – travel + –time+
Program description - Control adjust | Winged models
Now use the selection keys of the left or right touch pad
to select the desired input out of the list if the respective
plug-in location on the transmitter board is occupied...
I5 GL S11 --- 0% +100%
I6 GL fr --- 0% +100%
I7 GL fr --- 0% +100%
EI GL fr --- 0% +100%
Nor mal
TYP SEL
Offset – travel +
... or switch the entry to "fr" if the input is to be decou-
pled from a transmitter control. In this case, or even
when a non-existent transmitter control is assigned, the
servo corresponding to this input will be in its neutral
position and can only be controlled via mixers.
Switch assignment
If the input is to be actuated like a switch module, the
input can alternatively be assigned to a switch.
A simple switch can be used to switch back and forth
between two limit values, for example motor On/Off.
A 3-way momentary or toggle switch, see appendix,
achieves the same effect as a 2-channel switch mod-
ule, for example motor Off/Half/Full.
Use the selection keys to move into the column above
the switch symbol label. Briefly tap the centre
SET key of the right touch pad to activate the option
for assigning a switch.
+100% 0.0 0.0
+100% 0.0 0.0
+100% 0.0 0.0
+100% 0.0 0.0
–time+
119