Table of Contents
Advertisement
FAIL SAFE ALL (global fail-safe setting)
This sub-menu allows servo fail-safe positions to be
established at the "push of a button" in a similar man-
ner to that described on page 224 for the »Fail Safe«
menu.
Switch to the "FAIL SAFE ALL" line and activate the
value field by touching the centre
SET
touch pad. "NO" will be displayed in inverse video.
Then adjust the parameter to "SAVE" with one of the
selection keys of the right touch pad. Now, using the
operating elements of the transmitter, move all servos
to the desired fail-safe position you assigned or want
to assign in the line "MODE" "FAI(L) SAFE". The cur-
rent position of the control for the channel which was
just set is shown in the bottom "Position" line:
TELEMETRY
RX FAIL SAFE V3.98
TELEMETRI RCV
OUTPUT CH: 01
INPUT
CH: 01
SETTING & DATAVIEW
MODE
: FAI-SAFE
F.S.POS. : 1670µsec
SENSOR SELECT
DELAY
: 0.75sec
RF STATUS VIEW
FAIL SAFE ALL:
POSITION : 1670µsec
VOICE TRIGGER
After a tap on the centre
SET
key of the right touch
pad, the display will change again, from "SAVE" to
"NO". The saved the positions of all servos affected
by this measure and adopted them in parallel to
the line "F.S.Pos." and the display then immediately
shows the following for the current OUTPUT CH
(servo connection):
250 Program description - Telemetry
TELEMETRY
TELEMETRI RCV
SETTING & DATAVIEW
SENSOR SELECT
RF STATUS VIEW
key of the right
VOICE TRIGGER
Switch off the transmitter and check the fail-safe posi-
tions based on the servo throws.
"Fail Safe" in combination with "Channel Mapping"
In order to ensure that the mapped servos – that is to
say servos which are controlled from a common con-
trol channel (INPUT CH) – react the same way even
in the event of a failure, the corresponding settings of
the INPUT CH determine the behavior of the mapped
BIND. 1
servos!!!
Therefore, the servo connections 6, 7 and 8 of a
receiver are mapped with one another, whereby the
OUTPUT CH (servo connections) 06, 07 and 08 are
SAVE
assigned as INPUT CH of the same respective con-
trol channel "04" ...
TELEMETRY
TELEMETRI RCV
SETTING & DATAVIEW
SENSOR SELECT
RF STATUS VIEW
VOICE TRIGGER
RX FAIL SAFE V3.98
OUTPUT CH: 01
BIND. 1
INPUT
CH: 01
MODE
: FAI-SAFE
F.S.POS. : 1670µsec
DELAY
: 0.75sec
FAIL SAFE ALL: NO
POSITION : 1670µsec
RX FAIL SAFE V3.98
OUTPUT CH: 06
BIND. 1
INPUT
CH: 04
MODE
: FAI-SAFE
F.S.POS. : 1670µsec
DELAY
: 0.75sec
FAIL SAFE ALL: NO
POSITION : 1670µsec
TELEMETRY
RX FAIL SAFE V3.98
OUTPUT CH: 07
TELEMETRI RCV
INPUT
CH: 04
SETTING & DATAVIEW
MODE
: FAI-SAFE
F.S.POS. : 1230µsec
SENSOR SELECT
DELAY
: 0.75sec
RF STATUS VIEW
FAIL SAFE ALL: NO
POSITION : 1670µsec
VOICE TRIGGER
TELEMETRY
RX FAIL SAFE V3.98
TELEMETRI RCV
OUTPUT CH: 08
INPUT
CH: 04
SETTING & DATAVIEW
MODE
: FAI-SAFE
F.S.POS. : 1770µsec
SENSOR SELECT
DELAY
: 0.75sec
RF STATUS VIEW
FAIL SAFE ALL: NO
POSITION : 1670µsec
VOICE TRIGGER
... the INPUT CH 04 determines the fail-safe behavior
of these three servos connected to the control chan-
nel 4 completely independently of the individual set-
tings of the respective OUTPUT CH:
TELEMETRY
RX FAIL SAFE V3.98
TELEMETRI RCV
OUTPUT CH: 04
INPUT
CH: 04
SETTING & DATAVIEW
MODE
: FAI-SAFE
F.S.POS. : 1500µsec
SENSOR SELECT
DELAY
: 0.75sec
RF STATUS VIEW
FAIL SAFE ALL: NO
POSITION : 1670µsec
VOICE TRIGGER
This is also the case, for example, if this is mapped
with INPUT CH 01:
TELEMETRY
RX FAIL SAFE V3.98
OUTPUT CH: 04
TELEMETRI RCV
INPUT
CH: 01
SETTING & DATAVIEW
MODE
: FAI-SAFE
F.S.POS. : 1420µsec
SENSOR SELECT
DELAY
: 0.75sec
RF STATUS VIEW
FAIL SAFE ALL: NO
POSITION : 1670µsec
VOICE TRIGGER
BIND. 1
BIND. 1
BIND. 1
BIND. 1
Advertisement
Table of Contents
