Table of Contents
Advertisement
built-in loudspeakers or the transmitter's headset con-
nector. The fourth line of this menu is used to record
the transmitter owner's name. Select the characters
for this from an extensive character list on the second
display screen, which can be reached via the
symbol with a brief tap on the centre
right touch pad:
!"#$%&'()
+,–./0123456789:;
@ACDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
`abcdefghijklmnopqrstuvwxyz{|}~
¢ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÖÜ
H-J
Owners name
The same applies to the pre-sets for "Modulation"
and "DSC Output" (page 94 and 100).
The pre-set for "Pitch min" (page 109) is a matter of
personal control habits. The pre-sets established here
for "Stick mode", "Modulation", "DSC Output" and
"Pitch forward/back" will be initially adopted when
a new model memory is created but they can also be
freely changed within a given model memory location
to any other available option.
The settings in the "Top/Bottom LCD Contrast" lines
determine the legibility of the given displays under
poor light conditions and the setting in the "Display
light" line determines how long display lighting re-
mains illuminated after the transmitter is switched on
without any actuation of a control afterward or after
the last control actuation. The selection of "yes/no" in
the "Power-on/off beep" line determines whether the
"recognition melody" is to sound when the transmit-
ter is switched off or on again. The "Battery type"
line specifi es whether the transmitter is supplied with
current from a "NiMH or a "Lith." battery, and the
"Battery warning" line below it specifi es the voltage
at which the transmitter's low-voltage warning should
trigger. Do not enter a value that is too low here, so
you have enough time to land your helicopter.
The setting made in the "Stick warning" line de-
termines how long the transmitter will wait after the
last actuation of an operating element before issuing
visual and acoustic warning signals to indicate it is
SET
key of the
still switched on. Following the warning, you still have
about three minutes to actuate the transmitter so
the warning will abate. Otherwise the transmitter will
?
switch itself off when this time expires.
Later on, the ten "Own phase name" lines can be
used to create one's own phase names if none of the
pre-set phase names appear appropriate.
The value set in the "Touch Sense" line is a matter of
adapting the transmitter to personal preferences.
Sandb
In the "DATA SEL." line you can specify which abuts
the two possible data logs to the located under the
left front cover Data socket. By default, it is the data
output on the Smart-Box, No. 33700, suitable "telem-
etry" protocol.
Finally, if you are using a Bluetooth headset, you
can bind and confi gure it as described in the instruc-
tions supplied with the optional Bluetooth module, No.
33002.5; see the section entitled "BT Headset".
Once these settings have been taken care of, com-
missioning continues with the menu ...
Once these settings have been taken care of, com-
missioning continues with the menu ...
"Model select"
Use the selection keys to pick a free memory loca-
tion ...
01
02
03
04
05
06
(page 73)
00:12h
R16
free
free
free
free
free
... and call it up with a brief tap on the centre
of the right touch pad. In the display which then ap-
pears, use the key of the left or right touch pad ...
Select model type (free model memor y)
... to select the "helicopter" model type. The display
immediately switches to the base screen if the selec-
tion is confi rmed by a brief tap on the centre
of the right touch pad.
Notes:
•
If the "Select model type" option has been
opened, the process cannot be cancelled.
Even if you switch off the transmitter, this
selection must be made! In any case, you can
undo this by subsequently deleting the respective
model memory.
•
If it appears the warning „Throttle too high", it
can be deleted by pushing the default the throttle
limiter assigned to right side proportional rotary
slider on the back fence or moving the throttle /
pitch control stick of your transmitter to the idle or
Pitch min position.
•
If battery voltage is too low, the model switchover
cannot be made due to reasons of safety. An
appropriate message will appear in the screen:
not possible now
voltage too low
Once this fi rst hurdle is cleared, the connection of the
receiver built into the model at this model memory
must be made in the menu ...
Programming examples - Helicopter models
SET
key
SET
key
329
Advertisement
Table of Contents
