Table of Contents
Advertisement
The names assigned to given flight phases then ap-
pear in the second-from-the-bottom display line, e. g.
«Normal».
Note:
As a rule, input 6 must kept "free" for a
helicopter model. On this, see "Throttle" on
the next double page.
Basic procedure
1. Use the selection keys of the left or right
touch pad to select the desired input: I5, Thr6,
Gyr7, I8 ... 15 or Tl16.
2. If necessary, use the selection keys of the left
or right touch pad to select the desired column.
SET
3. Briefly tap the centre
key of the right touch
pad. The corresponding input field is shown
highlighted.
4. Operate the chosen operating element or set the
desired value with the selection keys of the right
touch pad.
SET
5. Briefly tap the centre
key of the right touch
pad to complete data entry.
6. A simultaneous tap on the or keys of the
right touch pad (CLEAR) will any setting made
back to its respective default value.
Column 2, "typ"
Similar to the previously described »Stick mode«
menu, this column can be used to define whether
further settings for the given input are to have a
"GL(obal)" or a "PH(ase-specific)" effect. Do this by
using the selection keys of the left or right touch pad
to select the desired input 5 through 16 in the column
labeled "TYP".
I5
GL
fr
---
0%
+100%
fr
---
Thr6
GL
0%
+100%
Gyr7
GL
fr
---
0%
+100%
E8
GL
fr
---
0%
+100%
Normal
TYP SEL
Offset
– travel +
"GL":
The settings for the input in question affect all
flight phases programmed (if any) and thus
act "globally" on the model memory in ques-
tion.
"PH":
The settings for this input take effect per
flight phase and must therefore be configured
separately for each flight phase.
Note:
See page 154 for more information about flight
phases.
Column 3, "Transmitter control/switch
assignment"
Using the selection keys of the left or right touch
pad to select an input: I5, Thr6, Gyr7, I8 ... 15 or Tl16.
Transmitter control assignment
Use the selection keys to move into the column la-
belled SEL. After completing the activation of trans-
mitter control assignment by tapping the centre
key of the right touch pad, the message shown below
will appear in the display:
I5
GL
fr
Thr6
GL
fr
Gyr7
GL
fr
I8
GL
fr
Nor mal
TYP SEL
Now actuate the desired transmitter control: The no-
+100%
0.0 0.0
tice window will disappear and the designation of the
+100%
0.0 0.0
selected transmitter control will appear in the trans-
mitter control assignment window.
+100%
0.0 0.0
+100%
0.0 0.0
I5
GL
S11 ---
Thr6
GL
fr
–time+
fr
Gyr7
GL
E8
GL
fr
Nor mal
TYP SEL
Alternatively, the centre
pad can be tapped for a second time while the notice
window, see above, is still on the display:
I5
GL
fr
Thr6
GL
fr
Gyr7
GL
fr
E8
GL
fr
Nor mal
TYP SEL
Now use the selection keys of the left or right touch
pad to select the desired input out of the list if the
respective plug-in location on the transmitter board is
occupied or switch the entry to "fr" if the input is to be
SET
decoupled from a transmitter control. In this case, or
even when a non-existent transmitter control is as-
signed, the servo corresponding to this input will be
Program description - Control adjust | Helicopter models
---
0%
+100%
+100%
0.0 0.0
---
Move desired
0%
+100%
+100%
0.0 0.0
---
control adj.
0%
+100%
+100%
0.0 0.0
---
0%
+100%
+100%
0.0 0.0
Offset
– travel +
–time+
0%
+100%
+100%
0.0 0.0
---
0%
+100%
+100%
0.0 0.0
---
0%
+100%
+100%
0.0 0.0
---
0%
+100%
+100%
0.0 0.0
Offset
– travel +
–time+
SET
key of the right touch
---
0%
+100%
+100%
0.0 0.0
---
0%
+100%
+100%
0.0 0.0
---
0%
+100%
+100%
0.0 0.0
---
0%
+100%
+100%
0.0 0.0
Offset
– travel +
–time+
123
Advertisement
Table of Contents
