GRAUPNER MC-32 Manual page 277

Winged model stick mode
"MODE 1" (Throttle at right stick) "MODE 2" (Throttle at left stick)
elev. down full throttle full throttle
elev. up idle idle
"MODE 3" (Throttle at right stick) "MODE 4" (Throttle at left stick)
elev. down Motor Vollgas full throttle
elev. up idle idle
Helicopter model stick mode
"MODE 1" (Throttle at right stick) "MODE 2" (Throttle at left stick)
pitch axis throttle throttle
pitch axis throttle throttle
"MODE 3" (Throttle at right stick) "MODE 4" (Throttle at left stick)
pitch axis Motor/Pitch throttle
pitch axis throttle throttle
Use the  selection keys of the left or right touch
pad to select the "Stick mode" line. The option field
will be framed.
G E N E R A L B A S IC SE T T IN G S
Voice volume
elev. down
Vario volume
Owners name
Pre-set stick mode
elev. up
Tap on the SET key briefly. The currently displayed
elev. down
stick mode will be displayed in inverse video. Now
use the selection keys of the right touch pad to select
the variant, from 1 to 4, you most frequently use. In
the future this will be used for newly initialized model
elev. up
memories in the Stick mode line of the »Basic set-
tings, model« menu (page 82 ... 93), but can be
changed on an individual basis for up to 80 model
memories.
pitch axis Following a simultaneous tap on the  or  keys
of the right touch pad (CLEAR), the display will return
to stick mode "1".
With another tap on the
pitch axis
tion field will be deactivated again to permit a change
to another line.
pitch axis
Pre-set modulation
Standard equipment for the
includes a HoTT transmitter module and, under the
right front cover – as viewed from the front – a connec-
pitch axis
tor socket for an external RF module, see page 27.
Additionally, a transmitter-internal iFS RF module can
be installed and connected. On a model-specific ba-
sis, the transmitter can be set to use the modulation
of any one of these three RF modules by appropri-
ately selecting "HoTT", "EXT. PPM" or "INT. PPM" in
the "Pre-set modulation" line of the »Basic settings,
model« menu (page 82 ... 93).
The most frequently used variant should logically
be selected for the "Pre-set modulation" line in the
H-J Sandbrunner 7 fr –––
"General Basic Settings" menu. In the future this will
7 fr –––
be used for newly initialized model memories, but can
be changed on an individual basis for up to 80 model
H-J Sandbrunner
memories.
1
Briefly tap the centre
SEL
Now use the selection keys of the right touch pad to
select the variant from among "HoTT", "EXT. PPM"
and "INT. PPM".
A simultaneous tap on the  or  keys of the
right touch pad (CLEAR) will return the display back
ESC SET
or key, the selec-
to modulation "HoTT".
With a brief tap on the
field is deactivated to permit a switch to another line.
Pre-set DSC Output
mc-32 transmitter
In the line with the same name in the »Basic set-
tings, model« menu (page 89 ... 100), a separate
specification can be made from among the four
available modulation types which is specific to each
model memory and will then provided at the DSC
socket. This choice primarily influences the maximum
number of control channels which can be attached to
the DSC (direct servo control) socket, and thus also
available to a flight simulator or teacher/pupil system.
By selecting "PPM10" this will be control channels 1
... 5, for "PPM16" channels 1 ... 8, for "PPM18" chan-
nels 1 ... 9 and for "PPM24" channels 1 ... 12.
SET key of the right touch pad:
G EN ER AL BASIC SET T I N G S
Touch-beeps vol. H-J Sandbrunner 7
Owners name H-J Sandbrunner
Pre-set stick mode
Pre-set modulation
SET or ESC key, the selected
Program description - Basic settings
fr –––
1
HoTT
SEL
277