Table of Contents
Advertisement
B A S I C
S E T T I N G , M O D E L
Rcv Ch Map
R16 R08
RF transmit
RF range test
DSC Output
SET SET
In a manner similar to "Pre-set stick mode", in this
»General basic settings« menu the selection made
for the "Pre-set DSC Output" line will determine which
of the four possible modulation types will be adopted
as the default variant for a newly initialized model
memory.
If necessary, use the selection keys of the left
or right touch pad to switch to the "DSC Output" line
then, with a brief tap on the centre
right touch pad, activate the value window:
G EN ERAL BA SIC SET T IN G S
Owners name
H-J Sandbrunner
H-J Sandbrunner
Pre-set stick mode
Pre-set modulation
Pre-set DSC Output
Now a choice can be made from among the four pos-
sible modulation types: "PPM10", "PPM16", "PPM18"
and "PPM24", with the selection keys of the right
touch pad. Another tap on the centre
right touch pad will conclude the entry.
A simultaneous tap on the or keys of the
right touch pad (CLEAR) will reset this option back to
"PPM10".
278 Program description - Basic settings
Pre-set Pitch min
n/a
n/a
In a manner similar to the previously described op-
on
tions "Stick mode" and "DSC Output", enter the pre-
99s
ferred actuation direction for the throttle/pitch stick
on this line so the choice will already be present by
PPM10
default for model memories newly initialized in the
SEL
SET
future. The functionality of all other helicopter program
options (to the extent they affect throttle and/or pitch)
are dependent on this setting; in other words the
throttle curve, idle trim, Channel 1 tail rotor mixer,
etc.
This means:
"fwd.":
minimum front pitch setting, the pitch stick
(C1) points away from the pilot.
"back": minimum rear pitch setting, the pitch stick
SET
key of the
(C1) points towards the pilot.
A simultaneous tap on the or keys of the
right touch pad (CLEAR) will set this option to "back".
Note:
The C1 stick's control direction for "Throttle
1
min front/rear" in the fixed-wing program can
HoTT
be changed individually in the »Model
PPM10
type« menu (page 104).
SEL
Contrast, upper display / lower display
In assure optimal legibility of
under all weather and temperature conditions, their
contrast settings can be adjusted separately.
SET
key of the
Contrast for the forward display, located between the
switch panels, is adjusted by selecting the "Top LCD
contrast" line with the selection keys of the left or right
touch pad then briefly tapping on the centre
of the right touch pad.
(only relevant to helicopter models)
mc-32
HoTT displays
SET
key
G EN ER AL BASI C SET TI N GS
Pre-set DSC Output
Pre-set Pitch min.
Top LCD contrast
Bottom LCD contrast
Now display contrast can be adjusted in the value
field displayed in inverse video within a range of ±20
by using the selection keys of the right touch pad.
RX–S QUA: 100%
RX–S STR: 100%
RX–dBm:
33dBm
TX–dBm:
33dBm
L–PACK:
10ms
RX–VOLT:4.8
CH OUTPUT TYPE:ONCE
R-LOW V:4.6
RX–S QUA: 100%
RX–S STR: 100%
RX–dBm:
33dBm
TX–dBm:
33dBm
L–PACK:
10ms
RX–VOLT:4.8
CH OUTPUT TYPE:ONCE
R-LOW V:4.6
Contrast for the rear display, located between the
touch pads, is adjusted by selecting the "Bottom LCD
contrast" line with the selection keys of the left or right
touch pad then briefly tapping on the centre
of the right touch pad.
PPM10
rear
0
0
SEL
TMP
+22°C
TMP
+22°C
SET
key
Advertisement
Table of Contents
