Table of Contents
Advertisement
»Base settings, model«
To this end, switch to the line "Module".
BASIC SETTINGS, MODEL
Model name
Starlet
Info
2345g/090911
Stick mode
Module
HoTT
n/a
n/a
SEL
BD1 BD2 BD3 BD4
Note:
After confi rmation of the model selection in
the base screen, if you confi rm the message
appearing in the screen for a few seconds ...
BIND. N/A
OK
... with a tap on the
SET
key of the right touch pad,
this line will be accessed automatically.
"Binding type"
If your transmitter is equipped with the latest fi rmware
or has since been updated accordingly, you should
briefl y deal yet with the differences between the two
available HoTT synchronization methods before the
actual binding process. Set default "model":
B A S I C
S E T T I N G S ,
Info
Stick mode
Binding type
Module
HoTT
n/a
n/a
SEL
BD1 BD2 BD3 BD4
•
"Model" -specifi c bound receivers respond only
to signals of them explicitly allocated memory
model. One, possibly unintentional, operating on
330 Programming examples - Helicopter models
(from page 92)
an unallocated model memory is not possible.
•
"Global", ie specifi c sender, receiver bound to re-
spond to the signals of all model memories "their"
station! A "wrong" model memory if necessary to
recognize only the warning of the missing return
channel.
So If necessary, change the line "Binding type" and
1
change the setting accordingly:
n/a
n/a
B A S I C
Info
Stick mode
Binding type
Module
HoTT
"Module"
In this line the binding process between model mem-
ory and receiver is initiated, as described in detail on
page 94. Otherwise, you cannot address the receiver.
Afterward, use the selection key of the left or right
four-way button to move up to the fi rst line and begin
with the actual model programming in the "Model
name" line:
BASIC SETTINGS, MODEL
Model name
Info
M O D E L
Stick mode
Module
HoTT
1
Model
n/a
n/a
... which must be assembled from characters avai-
lable on the second page of the "Model name" line:
S E T T I N G S ,
M O D E L
1
Global
n/a
n/a
n/a
n/a
SEL
BD1 BD2 BD3 BD4
Starlet
2345g/090911
1
n/a
n/a
n/a
n/a
SEL
BD1 BD2 BD3 BD4
!"#$%&'()
+,–./0123456789:;
@ACDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
`abcdefghijklmnopqrstuvwxyz{|}~
¢ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÖÜ
Model name
Starle
After entering the "Model name", the settings adopt-
ed from »Basic settings« for "Stick mode" and
"DSC Output" are to be checked and changed as
necessary for the given memory location.
The entry fi eld in the "Info" line can be used if needed
for a notice of up to 15 characters in length. This
notice will then be helpful in the selection of models
and so on.
Another option is to be activated in the "Autorota-
tion" line. Even if you are not an advanced pilot, the
autorotation switch should at least be set as an emer-
gency shutoff switch for the motor.
Do this by selecting the "Autorotation" line with a
brief tap on the centre
SET
key of the right touch
pad, activate the switch assignment, assign a 2-way
switch, e. g. "2", and put it in its "ON" position.
BASIC SETTINGS, MODEL
RF transmit
RF range test
DSC Output
Autorotation
SET
The selected switch should be in a location on the
transmitter which is easily within reach – without letting
loose of a stick – e. g. above the pitch stick.
?
on
99s
PPM10
2I
SET
Advertisement
Table of Contents
