Table of Contents
Advertisement
travel +" as well as the offset value and the mixer
proportion set in the "Multi-flap menu" of the »Wing
mixers« menu, see further below.
Leave the (control) "- travel +" at its standard sym-
metric settings of +100 % and the offset value at
0 %. Specifying a symmetric or asymmetric time for
smooth switching between the three switch posi-
tions – in the example "1.0 s 1.0 s" – in the column
"- time +" is recommended:
I5
GL fr
---
0%
+100%
I6
PH
Sl1
---
0%
+100%
---
I7
GL
fr
0%
+100%
I8
GL Cn1
---
0%
+100%
Normal
Typ
SEL
offset
– travel +
In the "Multi-flap menu" of the ...
»Wing mixers«
(beginning page 160)
... menu, subsequently change only the values for
"FL.pos" and "FL" in the «Thermal» flight phase:
•
FL.pos
It is here that AI and FL positioning takes place
during the «Thermal» flight phase in the event that
the assigned control (proportional control or 3-way
switch) is in its neutral or middle position.
AI
+100%
Ail-tr.
+100%
Diff.
0%
+33%
0%
FL.pos
+100%
–9%
+100%
0% +100%
FL
Thermal
AI
•
FL
Enter in this line the share of influence for aileron
and camber flap servos, when used as camber
flaps, is to be produced by the selected control
(see above) or 3-way switch. Be sure to set these
values low enough that the flaps can be controlled
with appropriate sensitivity, for example:
AI
AiI-tr.
Diff.
+100%
0.0 0.0
Fl.pos
+100%
1.0 1.0
FL
+100%
0.0 0.0
Thermal
+100%
0.0 0.0
A simultaneous tap on the or key com-
–time+
bination of the right touch pad (CLEAR) will reset
changed values back to their standard default values.
Note:
Due to the improved lift distribution, the
degree of mix ratios should be set so that the
camber flaps are slightly "lower" than the
ailerons.
With a simultaneous tap on the keys of the left
touch pad, the reaction of the AI and FL servos can
be checked in the »Servo display« by actuation of
the selected camber flap control. (Push the C1 stick
to the front position so that the "AI" and "FL" posi-
+66%
0%
tions can be better followed on actuation of the cor-
+66%
0%
responding control.)
+33%
0%
Caution:
–11%
+100%
0%
With aileron actuation the bars of
+100%
WK2
the »Servo display« move in the
FL
same manner, for camber flap
actuation they will move in the opposite
manner.
+100%
+66%
0%
+100%
+66%
0%
0%
+33%
0%
+33%
0%
+100%
–9%
+100%
–11%
+100%
0%
+20%
+20% +25%
+25%
WK2
AI
FL
•
In the control's middle position, the – example's –
"FL-pos." setting only has a -9 % effect for the AI
and -11 % for the FL.
•
In one transmitter control end-position, AI and FL
are again closer to the neutral position because
the mix ratio specified in the example reduces the
FL.pos setting, whereas ...
•
... in the other limit position, AIL and FL reach
the maximum downward offset prescribed by the
mixer percentage.
In order to set a – corrective – admix for the eleva-
tor, exit the "Multi-flap menu" and return to the base
screen of the »Wing mixers« menu:
W I N G
M I X E R S
Multi-flap menu
Brake settings
Aileron
2
3
rudder
+50%
Flaps
6
4
aileron
+5%
Thermal
In the two limit positions of the three-stage switch the
elevator is moved symmetrically in this example with
+5 % (true to side). If, on the other hand, you use a
proportional control, the elevator is deflected accord-
ing to the degree for the control position.
Then make the settings for the "Speed" flight phase in
the same manner.
Notes:
•
The digital trimming of transverse, altitude
and side work independently of these
settings – depending on the setting
selected in the»Stick mode« menu, page
114 – "global" or for each "phase".
•
All setting values are model-dependent. Carry out
the settings on your finished model and/or during
the flight.
Programming examples - Using flight phases
–––
+5%
–––
317
Advertisement
Table of Contents
