Table of Contents
Advertisement
On the other hand, should the LED on the receiver
blink red for longer than about 10 seconds, the
binding process has failed. In this case the screen
will continue to show the status as "n/a". If this
should happen, try changing the position of anten-
nas then repeat the entire procedure.
•
Receiver GR-12L
At the receiver, the red LED lights. Press and hold
the SET button on the receiver until the red LED
goes out after about 3 seconds for a further 3 sec-
onds. You can now release the SET button on the
receiver. As long as the LED is off, the receiver is
in bind mode. Start now-as described above-within
these 3 s to bind the receiver to the current model
memory. If the LED of the receiver is still dark and
the display in the transmitter changes to "b", the
binding process has been completed success-
fully. However, the red LED will light up red again
at the receiver, the binding process has failed.
At the same time appear in the line "module" of
the display again "n / a". If necessary, change the
positions of the antennas involved and repeat the
entire procedure.
Binding other receivers
The binding channel you have chosen is already
bound (as indicated by the "bind" status). This bind-
ing is to be replaced by another. After initiating the RF
bind process, instead of displaying "BINDING", the
message shown below appears.
B A S I C
S E T T I N G , M O D E L
RF
Model name
Graubele
Info
is tur ned
1234g/111111
Stick mode
off
Module
HoTT
geb.
geb.
OK
SEL
BD1 BD2 BD3 BD4
Drop down two lines in the screen and switch off the
RF module as described on the page in section "RF
module". Afterward, return again to the "Module" line
and restart the binding process as described above.
Alternatively, the transmitter can be switched off
briefl y then, after switching it back on again, respond
to the message window that appears ...
... with "OFF" ...
... then confi rm the selection with a brief tap on the
centre
SET
key of the right touch pad. From the base
screen jump again into the "Module" line of the »Ba-
sic settings, model« menu and restart the binding
process.
Dissolving a bond
Proceed as described above to initiate the binding
process but WITHOUT fi rst putting a receiver in bind-
ing readiness.
1
n/a
n/a
Please select
RF on/off?
ON
OFF
Please select
RF on/off?
ON
OFF
Program description - Base setup models | Winged models
EXT.
(PPM signal at DSC sock-
et)
If your transmitter is fi tted with a non-Graupner exter-
nal RF module connected to the DSC / Data socket,
you can switch between the standard internal HoTT
RF module and the external module when you switch
model memories in the "Module" line by choosing
either "HoTT", "EXT.", or "SP.", as described in the fol-
lowing section.
You can now use the arrow button of the right-hand
four-way button to move to the fi rst Value fi eld in the
"Module" line before pressing the central
of the right-hand four-way button:
B A S I C
S E T T I N G , M O D E L
Model name
Graubele
Info
1234g/111111
Stick mode
HoTT
bind bind
Module
SEL
BD1 BD2 BD3 BD4
In the active Value fi eld you should now use the Se-
lect buttons to choose "EXT." or – if appropriate – the
"SP." mode (described below) instead of "HoTT".
When you select "EXT.", the HoTT-specifi c value fi elds
are replaced by the modulation type already selected
in the "DSC output" line; see page 89:
B A S I C
S E T T I N G , M O D E L
Model name
Graubele
Info
1234g/111111
Stick mode
EXT. PPM
Module
SEL
The lines of the "Receiver output" and "Range test"
options (described below) are also suppressed, as
SET
button
1
n/a
n/a
1
PPM10
85
Advertisement
Table of Contents
