D Band Stacking Register; D Data Mode With Filter Width Setting - Icom IC-7200 Advanced Instructions

Previous view
11
CONTROL COMMAND
Controlling the radio with CI-V
■
D Command table (Continued)
Cmd. Sub cmd. Data
1A 0343 0
1
0344 0
1
0345 0
1
0346 0
1
0347 0
1
0348 0
1
0349 0 to 255 Send/read reference frequency set
0350 0 to 255 Send/read noise blanker level set
0351 0 to 255 Send/read noise blanker width set
0352 0 to 15 Send/read NR level set
0353 0 to 255 Send/read VOX gain set
0354 0 to 255 Send/read Anti-VOX gain set
0355 0 to 20 Send/read VOX delay set
0356 0 to 10 Send/read speech compressor level
04 —
05 0
1
06 0
1
2
1C 00 0
1
01 0
1
2
Description
Send/read MIC UP/DOWN keyer (HM-
36) OFF
Send/read MIC UP/DOWN keyer (HM-
36) ON
Send/read SSB mode selection OFF
(inhibition)
Send/read SSB mode selection ON
(selectable)
Send/read CW mode selection OFF
(inhibition)
Send/read CW mode selection ON (se-
lectable)
Send/read RTTY mode selection OFF
(inhibition)
Send/read RTTY mode selection ON
(selectable)
Send/read AM mode selection OFF (in-
hibition)
Send/read AM mode selection ON (se-
lectable)
Send/read CI-V transceive function
OFF
Send/read CI-V transceive function ON
(0=0% to 255=100%)
(0=0% to 255=100%)
(0=0% to 255=100%)
(0=0 to 15=15)
(0=0% to 255=100%)
(0=0%, 255=100%)
(0=0.0 sec. to 20=2.0 sec.)
(0=0 to 10=10)
Send/read DATA mode with filter set
(see to the right for detail)
Send/read Sharp selection for DSP fil-
ter shape
Send/read Soft selection for DSP filter
shape
Send/read manual notch width Wide
Send/read manual notch width Mid
Send/read manual notch width Narrow
Send/read the transceiver's status RX
Send/read the transceiver's status TX
Antenna tuner OFF (through)
Send/read Antenna tuner ON
Send/read Manual tuning selection

D Band stacking register

Command: 1A 01
To send or read the desired band stacking register's
contents, a combination of the frequency band and the
register codes ("01" is fixed as the register code) as
follows are used.
For example, when sending/reading the contents in
the 21 MHz band, the code "0701" is used.
• Frequency band codes
CODE BAND
01 1.8 MHz
02 3.5 MHz
03 7 MHz
04 10 MHz
05 14 MHz
06 18 MHz
07 21 MHz
08 24 MHz
09 28 MHz
10 50 MHz
11 General

D Data mode with filter width setting

Command: 1A 04
The following data sequence is used when sending or
reading the data mode with filter width setting.
q w
X X X X
First parameter
00=Data mode OFF
01=Data mode ON
11-5
FREQUENCY RANGE
1.800000 – 1.999999
3.400000 – 4.099999
6.900000 – 7.499999
9.900000 – 10.499999
13.900000 – 14.499999
17.900000 – 18.499999
20.900000 – 21.499999
24.400000 – 25.099999
28.000000 – 29.999999
50.000000 – 54.000000
Other than above
Second parameter
00=Data mode OFF
01=FILTER Wide
02=FILTER Mid
03=FILTER Narrow