Icom IC-7200 Advanced Instructions page 118

Previous view
11
CONTROL COMMAND
Controlling the radio with CI-V
■
D Command table (Continued)
Cmd. Sub cmd. Data
1A 02 0 to 40 Send/read the selected filter width
0301 0 to 255 Send/read RF power setting
0302 0 to 255 Send/read MIC gain setting
0303 0 to 255 Send/read Key speed level setting
0304 0 to 120 Send/read CW Tone Pitch setting
0305 0 to 255 Send/read CW side tone setting
0306 0
1
0307 0
1
0308 0
1
2
0309 0
1
2
3
0310 0
1
0311 0
1
2
0312 0
1
0313 0
1
0314 0 to 255 Send/read beep gain
0315 0
1
0316 0
1
2
0317 0
1
0318 0
1
0319 0
1
0320 0
1
0321 0
1
0322 0
1
Description
( SSB, CW, RTTY: 0=50 Hz to
40/31=3600/2700 Hz;
AM: 0=200 Hz to 39=8 kHz)
(0=minimum to 255=100%)
(0=0% to 255=100%)
(0=6 wpm to 255=60 wpm)
(0=300 Hz to 120=900 Hz; 5 Hz steps)
(0=0% to 255=100%)
Send/read CW side tone level limit
OFF
Send/read CW side tone level limit ON
Send/read Twin Peak filter OFF
Send/read Twin Peak filter ON
Send/read RTTY mark frequency
1275 Hz
Send/read RTTY mark frequency
1615 Hz
Send/read RTTY mark frequency
2125 Hz
Send/read RTTY shift width 170 Hz
Send/read RTTY shift width 200 Hz
Send/read RTTY shift width 425 Hz
Send/read RTTY shift width 850 Hz
Send/read RTTY keying polarity Nor-
mal
Send/read RTTY keying polarity Re-
verse
Send/read LCD brightness OFF
Send/read LCD brightness Dark
Send/read LCD brightness Bright
Send/read confirmation beep OFF
Send/read confirmation beep ON
Send/read Band edge beep OFF
Send/read Band edge beep ON
(0=0% to 255=100%)
Send/read Beep gain limit OFF
Send/read Beep gain limit ON
Send/read Auto selection for [RF/SQL]
Send/read SQL selection for [RF/SQL]
Send/read RF+SQL selection
[RF/SQL]
Send/read Meter peak hold function
OFF
Send/read Meter peak hold function
ON
Send/read Quick Split function OFF
Send/read Quick Split function ON
Send/read Split Lock function OFF
Send/read Split Lock function ON
Send/read transmit frequency monitor
function with [RIT] key OFF
Send/read transmit frequency monitor
function with [RIT] key ON
Send/read Tuner Auto Start OFF
Send/read Tuner Auto Start ON
Send/read PTT Tune Start OFF
Send/read PTT Tune Start ON
Cmd. Sub cmd. Data
1A 0323
0324
0325 0 to 255 Send/read MOD input gain from USB
0326 0 to 255 Send/read speech level
0327
0328
0329
0330
0331
0332
0333
0334
0335
0336
for
0337
0338
0339 20 to 130 Send/read break-in delay time set
0340 28 to 45 Send/read CW keyer dot/dash ratio
0341
0342
11-4
Description
0 Send/read MIC selection for MOD input
connector during DATA OFF
1 Send/read ACC selection for MOD in-
put connector during DATA OFF
2 Send/read MIC+ACC selection for MOD
input connector during DATA OFF
3 Send/read USB selection for MOD in-
put connector during DATA OFF
0 Send/read MIC selection for MOD input
connector during DATA ON
1 Send/read ACC selection for MOD in-
put connector during DATA ON
2 Send/read MIC+ACC selection for MOD
input connector during DATA ON
3 Send/read USB selection for MOD in-
put connector during DATA ON
(0=0% to 255=100%)
(0=0% to 255=100%)
0 Send/read speech language English
1 Send/read speech language Japanese
0 Send/read speech speed Slow
1 Send/read speech speed Fast
0 Send/read S-level speech function
OFF
1 Send/read S-level speech function ON
0 Send/read speech capability
[MODE] key operation OFF
1 Send/read speech capability
[MODE] key operation ON
0 Send/read Scan speed Slow
1 Send/read Scan speed Fast
0 Send/read Scan Resume function OFF
1 Send/read Scan Resume function ON
0 Send/read Main Dial Auto TS function
OFF
1 Send/read Main Dial Auto TS Low
2 Send/read Main Dial Auto TS High
0 Send/read 1/4 dial speed function OFF
1 Send/read 1/4 dial speed function ON
0 Send/read mic. UP/DOWN speed Low
1 Send/read mic. UP/DOWN speed High
0 Send/read SSB/CW synchronous tun-
ing function OFF
1 Send/read SSB/CW synchronous tun-
ing function ON
0 Send/read LSB selection for the CW
carrier point
1 Send/read USB selection for the CW
carrier point
0 Send/read Break-IN function OFF
1 Send/read Semi Break-IN function ON
2 Send/read Full Break-IN function ON
(20=2.0 d to 130=13.0 dots)
(28=1:1:2.8 to 45=1:1:4.5)
0 Send/read CW paddle polarity Normal
1 Send/read CW paddle polarity Re-
verse
0 Send/read CW keyer type Straight
1 Send/read CW keyer type Bug-key
2 Send/read CW keyer type ELEC Key
with
with