Ricoh CL2000 Operating Instructions Manual page 6

Lower the inner cover slowly.
Hold the toner cartridge horizontally as
illustrated, and then shake it back and forth about
10 times.
ZHBH410E
Push the green lever to fasten the inner cover.
In the illustration, black cartridge is used as an example.
Important
❒ Do not open the shutter on the bottom of the toner
cartridge. Toner may spill.
ZHBH420E
Close the right cover of the printer slowly.
Remove the adhesive tapes.
ZHBH430E
INSTALLING THE TONER
Check the toner color and location are correct,
and then insert the toner cartridge vertically and
CARTRIDGE
slowly.
You can check the location for each toner cartridge by reading the
Open the upper left cover of the printer.
labels on the printer.
ZHBH441E
Take out the toner cartridge.
In the illustration, yellow cartridge is used as an example.
Sheet 1/2
Push the toner cartridge in the direction of the
arrow to fasten the toner cartridge.
ZHBH491E
ZHBH460E
Repeat steps to , to install the other color
toner cartridges.
Close the upper left cover of the printer.
ZHBH500E
ZHBH470E
Note
❒ If the toner cartridge is not set properly, you cannot
close the upper left cover of this printer.
LOADING PAPER
ZHBH910E
Caution
• When pulling the paper tray out, be careful not
to pull it strongly. If you do, the tray might fall
and cause personal injury.
Pull the paper tray out of the printer until it stops.
After that, lift it slightly, and then pull it out
completely. Place it on a flat surface.
ZHBH481E
ZHBY010E
Note
ATTACHING LEGAL-SIZE
❒ You cannot pull the Tray 1 out if the Bypass Tray is
SUPPORT TRAY
open.
Pull out the standard tray extension until it clicks.
(A, B).
ZHBY071E
Remove the adhesive tape and packing material.
Lift the standard tray extension with your finger,
(C), and then attach the legal-size support tray
(D).
ZHBY920E
Press "Push", and then adjust the rear guide to
the paper size you want to load.
Check both hooks of the legal-size support tray
are correctly engaged with the standard tray
extension.
ZHBY040E
Adjust the side guides to the paper size you want
to load.
The legal-size support tray's feet should pinch
the outside of the ribs. Check they are not resting
on top.
ZHBY060E
Load paper into the paper tray with the print side
up.
Important
❒ Make sure that the top of the stack is not higher
than the limit mark inside the tray.
❒ The rear and side guides should be set exactly to
the paper size to avoid paper misfeeds.
Slide the paper tray completely into the printer.
CONNECTING THE POWER CORD
Warning
• It is dangerous to handle the plug with wet hands.
Doing this may result in receiving an electric
shock.
Caution
• When you pull the plug out of the socket, grip
the plug, not the cord, to avoid damaging the
cord and causing a fire or an electric shock.
Important
❒ Be sure to connect the power plug to the socket or
the wall outlet firmly.
❒ The printer power must be off when plugging in
and removing the power cord.
ZHBHA1010N
Confirm that the printer's power switch is off. If it
is on, turn it off.
ZHBH730E
Attach the power cord to the socket on the back
of the printer.
ZHBHA1020N
ZHBH030E
Plug the other end securely into the wall outlet.
ZHBHA1030N
SELECTING THE PANEL
DISPLAY LANGUAGE
Follow the procedure to select a language.
Note
❒ You can select one of the following languages:
English, German, French, Italian, Dutch, Swedish,
Norwegian, Danish, Spanish, Finnish, Portuguese,
Czech, Polish or Hungarian.
❒ The default setting is English.
❒ If you want to use the English panel display, it is not
necessary for you to take the following procedures.
ZHBHA1040N
❒ The label for selected language can be stuck on the
control panel.
Go to sheet 2/2.