Table of Contents
Advertisement
8 NXDN CONVENTIONAL SYSTEM
8.4 Initiating an Individual Call After Ensuring That the Target Party Is Available for Communications (Individual Call
Note
• If the time configured for Initiating/Incoming Reset Time elapses while the transceiver is placed in the state mentioned at Step 1, the
transceiver resets the standby state, and the display reverts to the channel display. (Refer to
to Wait to Receive an Acknowledgment Message (Initiate/Incoming Reset Time) on page
• During Step 1, the transceiver can reject an incoming call by pressing the Side 1 key (Portable) or the Triangle key (Mobile).
• Pressing the PTT switch at Step 2 initiates an Individual Call to the transmitting transceiver. Not only receiving an acknowledgment
message, but also receiving an Individual Call makes the transmitting transceiver available for the communication.
If Automatic Response is enabled:
1
Receive a message requesting an acknowledgment.
An Alert Tone (Individual Call) sounds from the transceiver. If Selective Call Alert LED is enabled, the LED blinks orange or
blue. (Refer to
Transceiver Behavior When Receiving an Individual Call/ Paging Call on page
An acknowledgment message is automatically sent to the transmitting transceiver.
After sending the acknowledgment message, by receiving an Individual Call from the transmitting transceiver which has been
enabled for the communication, an Alert Tone (Individual Call) sounds from the transceiver. (Refer to
When Receiving an Individual Call/ Paging Call on page
Note
Pressing the PTT switch initiates an Individual Call to the transmitting transceiver. Not only receiving an acknowledgment message,
but also receiving an Individual Call makes the transmitting transceiver available for the communication.
Configuration using KPG-169D/ KPG-170D/ KPG-175D
•
Configuring the Alert Tone (Individual) (Unit ID List) (
•
Configuring the Alert Tone (Paging) (Unit ID List) (
•
Configuring the Alert LED Color (Individual) (Unit ID List) (
Individual)
•
Configuring the Alert LED Color (Paging) (Unit ID List) (
•
Configuring the Alert Tone (Individual Call) used in common in the NXDN Conventional system (
NXDN > Conventional > Alert Tone)
•
Configuring the Alert Tone (Paging Call) used in common in the NXDN Conventional system (
Conventional > Alert Tone)
•
Configuring the Alert LED Color (Individual Call) used in common in the NXDN Conventional system (
NXDN > Conventional > Alert LED Color)
•
Configuring the Alert LED Color (Paging Call) used in common in the NXDN Conventional system (
NXDN > Conventional > Alert LED Color)
Notifying the User with a Tone That a Call Request Has Been Initiated
(Call Request Tone)
The Call Request Tone is the function to sound a Call Request Tone from the transceiver when a call request for an
Individual Call (Individual Call Acknowledge Request) is initiated.
The Call Request Tone from the transceiver notifies the user that a call request for an Individual Call (Individual Call
Acknowledge Request) has been initiated. The user can initiate the communication after the call request has been
established.
Configuration using KPG-169D/ KPG-170D/ KPG-175D
Configuring the Call Request Tone to be enabled or disabled (
Individual Call Acknowledge Request)
FUNC (K)/Ver 1.20
65.)
59.)
Edit > NXDN > Unit ID List > Alert Tone > Individual)
See
Edit > NXDN > Unit ID List > Alert Tone > Paging)
See
Edit > NXDN > Unit ID List > Alert LED Color >
See
See
Edit > NXDN > Unit ID List > Alert LED Color > Paging)
See
Edit > NXDN > Conventional >
Configuring the Maximum Length of Time
59.)
Transceiver Behavior
See
Edit >
See
Edit > NXDN >
See
See
Edit >
CONTENTS
INDEX
Edit >
64
Advertisement
Table of Contents
