Kenwood ProTalk NX-240V16P Operating Manual

NX-240V16P/NX-340U16P
Operating Manual
FCC License Information
Your KENWOOD transceiver operates on communications frequencies which are subject to FCC (Federal
Communications Commission) Rules & Regulations. FCC Rules require that all operators using Private Land Mobile
radio frequencies obtain a radio license before operating their equipment. Application for license must be made on
FCC form 601, schedules D and H, and Remittance form 159.
FAX: Forms can be obtained by fax from the FCC Fax-On-Demand system. Call 1-202-418-0177 from your fax
machine and request document number 000601 for the form, schedules, and instructions.
MAIL: Forms can be ordered by telephone, and will be sent to you by first class mail. Call the FCC Forms Hotline at
1-800-418-FORM (1-800-418-3676).
INTERNET: Form 601 and instructions can be downloaded from the FCC Forms website at
http://www.fcc.gov/formpage.html
Before filling out your Form 601 application Technical Data section, you must decide on which frequencies you will
operate. See the frequency tables below.
QUESTIONS? Call the FCC for license application questions at 1-888-CALL-FCC (1-888-225-5322).
CHANNEL SETUP MODE
This transceiver allows you to reprogram each of the channels with different frequencies and QT (Quiet Talk)/ DQT
(Digital Quiet Talk)/ RAN (Radio Access Number) settings. The table below lists the default channel settings for
Analog and Digital modes. The transceiver comes in ANALOG MODE for both zones.
NX-240V16P
ANALOG MODE
Zone Channel Table Frequency
Type Number Number (MHz)
1 (1) 151.6250
2 (1) 151.6250
3 (1) 151.6250
4 (1) 151.6250
5 (1) 151.6250
6 (2) 151.9550
7 (2) 151.9550
Analog 8 (2) 151.9550
9 (2) 151.9550
10 (2) 151.9550
11 (20) 154.4900
12 (21) 154.5150
13 (10) 151.5125
14 (12) 151.6850
15 (5) 151.7000
16 (6) 151.7600
NX-340U16P
ANALOG MODE
Zone Channel Table Frequency
Type Number Number (MHz)
1 (1) 464.5000
2 (1) 464.5000
3 (1) 464.5000
4 (1) 464.5000
5 (1) 464.5000
6 (2) 464.5500
7 (2) 464.5500
Analog 8 (2) 464.5500
9 (2) 464.5500
10 (2) 464.5500
11 (22) 461.3625
12 (30) 464.4875
13 (32) 464.5375
14 (34) 466.0375
15 (36) 466.0875
16 (38) 466.1375
® DIGITAL
DIGITAL MODE
QT Zone Channel Table Frequency
(Hz) Type Number Number (MHz)
67.0 1 (1) 151.6250
77.0 2 (1) 151.6250
88.5 3 (1) 151.6250
179.9 4 (1) 151.6250
100.0 5 (1) 151.6250
67.0 6 (2) 151.9550
82.5 7 (2) 151.9550
Digital
94.8 8 (2) 151.9550
(NXDN)
179.9 9 (2) 151.9550
100.0 10 (2) 151.9550
67.0 11 (20) 154.4900
67.0 12 (21) 154.5150
67.0 13 (10) 151.5125
67.0 14 (12) 151.6850
67.0 15 (5) 151.7000
67.0 16 (6) 151.7600
DIGITAL MODE
QT Zone Channel Table Frequency
(Hz) Type Number Number (MHz)
67.0 1 (1) 464.5000
77.0 2 (1) 464.5000
88.5 3 (1) 464.5000
179.9 4 (1) 464.5000
100.0 5 (1) 464.5000
67.0 6 (2) 464.5500
82.5 7 (2) 464.5500
94.8 Digital 8 (2) 464.5500
179.9 (NXDN) 9 (2) 464.5500
100.0 10 (2) 464.5500
74.4 11 (22) 461.3625
79.7 12 (30) 464.4875
85.4 13 (32) 464.5375
91.5 14 (34) 466.0375
97.4 15 (36) 466.0875
103.5 16 (38) 466.1375
SELF PROGRAMMING MODE
TO CHANGE THE OPERATING FREQUENCIES OF CHANNELS
•
[1] With the transceiver power OFF, press and hold the PTT switch
and Side 1 key while turning the transceiver power ON.
Continue to hold the PTT switch and Side 1 key until the LED lights
orange and the transceiver announces "Self."
[2] Release the PTT switch and Side 1 key.
• The transceiver announces "Zone #" that you were operating.
• Pressing the Side 1 key or Side 2 key will toggle between Zone 1
and Zone 2.
• Press the PTT switch to choose the Zone that you want to modify.
• Then, the transceiver announces "Analog" or "Digital" whichever
the selected zone was operating.
• Pressing the Side 1 key or Side 2 key will toggle between "Analog"
and "Digital."
• Press the PTT switch to choose the mode that you want to operate
in the selected zone.
• Upon choosing the mode (above [2]), the transceiver announces
Zone#, Channel#, and "Channel."
[3] Rotate the Channel selector to your desired channel#.
To change the frequency of the selected channel, Press the PTT
switch.
To change the QT or DQT, press the Side 1 or 2 key to toggle
between "Channel", "QT", and "DQT". [If the channel is in ANALOG
RAN
Zone] and press the PTT.
1
To change the RAN or NXDN ID*, press the Side 1 or 2 to toggle
2
between "Channel", "RAN", and "NXDN ID," [If the channel is in
3
4
DIGITAL Zone] and press the PTT.
5
1
2
3
[4] Press the Side 1 / Side 2 key to increment/ decrement the table number,
4
5 to select a frequency, QT/DQT/RAN, and NXDN ID.
1
• Press and hold the Side 1 or Side 2 key to increment / decrement
1
the number by 5 at a time.
1
1
1
1
[5] Press the PTT switch to save the setting.
• A beep will sound.
• Repeat steps [3] to [5] to set up another channel.
RAN
1
2
[6] Turn the transceiver power OFF and then ON again to activate the
3
4
new settings.
5
1
2
3
4
5
1
1
1
1
Note: The transceiver will automatically return to normal operation if no action is performed for 20 seconds.
1
1
"Self"
Zone Selection
Choose a Zone
by side keys
Select by PTT
Mode Selection
Choose Analog or
Digital by side keys
Select by PTT
Channel Selection
Select a channel
to be set up.
• Channel Table
• QT/DQT/RAN
• NXDN (Digital) ID
[ANALOG]
Channel, QT, DQT
[DIGITAL]
Channel, RAN, NXDN ID
Select by PTT