A Tone/ B Tone/ C Tone/ D Tone; Auto Reset Timer; Clear To Transpond; Selective Call Alert Led - Kenwood TK-3180 Function Reference

21 2-TONE
Transpond Alert
Yes Off
Other than
No
Off
Other than
Yes
Off
!
Alert Tone
You can configure the Alert Tone to transmit when the
transceiver receives a call using 2-tone signaling.
You can select one of eight tone patterns configured in
the Alert Tone Pattern. (Refer to 4.7 Alert Tone Pattern.)
!
Configuration using KPG-89D
•
Configuring the Call Format (Refer to FPRG
6.10.2 Decode tab - Call Format.)
•
Configuring the Transpond function (Refer to
FPRG 6.11.2 Decode tab - Transpond.)
•
Configuring the Alert Tone (Refer to FPRG 6.11.2
Decode tab - Alert Tone.)
21.3.2 A Tone/ B Tone/ C Tone/
D Tone
This function allows you to configure the frequency of the
tones. You can configure the frequency between 288.5
and 3106.0 Hz.
!
Configuration using KPG-89D
•
Configuring the A Tone/ B Tone/ C Tone/ D Tone
(Refer to FPRG 6.11.2 Decode tab - A Tone/ B
Tone/ C Tone/ D Tone.)

21.3.3 Auto Reset Timer

The Auto Reset Timer is the duration from the time when
communication ends to the time when the 2-tone match
status is reset.
You can configure the Auto Reset Timer using KPG-89D.
You can also configure the operation after the Auto Reset
Timer is expired.
Table 21-4 Operation after the Auto Reset Timer is expired.
Auto Reset Timer
Off The Auto Reset Timer does not work.
The orange Selective Call Alert LED
LED indicator stops blinking when the Auto Reset
Timer expires.
The intermittent transmission of the Alert
Alert Tone stops when the Auto Reset Timer
expires.
92
Operation
The transceiver transmits the
Transpond Tone.
The transceiver transmits the Alert
Tone.
The transceiver transmits the Alert
Tone after it transmits the
Transpond tone.
Operation
Auto Reset Timer
Monitor
!
Configuration using KPG-89D
• Configuring the Auto Reset Timer (Refer to FPRG
6.11.2 Decode tab - Auto Reset Timer.)
• Configuring the LED (Refer to FPRG 6.11.2
Decode tab - LED.)
• Configuring the Alert (Refer to FPRG 6.11.2
Decode tab - Alert)
•
Configuring the Monitor function (Refer to FPRG
6.11.2 Decode tab - Monitor.)

21.3.4 Clear to Transpond

This function prevents the transceiver from performing
the Transpond function until the channel becomes
available.
You can enable/disable the Clear to Transpond function
using KPG-89D.
!
Configuration using KPG-89D
• Configuring the Clear to Transpond (Refer to
FPRG 6.11.2 Decode tab - Clear to Transpond.)

21.3.5 Selective Call Alert LED

This function makes the SelCall Alert LED blink when the
code is received.
You can enable/disable the Selective Call Alert LED using
KPG-89D. (Refer to 22.2 Selective Call Function.)
Note:
" The match status of 2-tone resets in the following conditions.
Table 21-5 Condition to reset the 2-tone Match Status
Operation
Press a key.
On-hook
Function Reference
Operation
The match status of the DTMF resets
when the Auto Reset Timer expires.
Condition
One of the following keys is pressed.
• PF Monitor key
• PF Monitor Momentary key
• PF Squelch Off key
• PF Squelch Off Momentary key
• PF Zone Up key
• PF Zone Down key
• PF Zone Up/Down key
• PF CH/GID Up key
• PF CH/GID Down key
• PF CH/GID Up/Down key
• PF Scan key
• PF Home CH/GID key
• PF Direct CH/GID 1 - PF Direct CH/GID 5
key
The microphone status becomes On-hook.
Version: 1.11