Fleetsync; Ptt Id Function; Caller Id Display; Ptt Id Sidetone - Kenwood TK-3180 Function Reference

22 FLEETSYNC

FleetSync, developed by Kenwood, utilizes MSK
(Minimum Shift Keying) modulation to exchange data
between transceivers. It identifies individual transceivers,
and allows for text messages and GPS data
communications.
You can also connect the transceiver to a PC or external
devices since FleetSync supports serial data
communication.

22.1 PTT ID Function

PTT ID is the function to transmit an identification code
when making a call.
A user can view the caller's ID with the received PTT ID.
The user can confirm the caller not only by voice, but also
through the display.
You can configure the PTT ID for each CH/GID. The PTT
ID is transmitted in the following timing.
ID.)
Table 22-1 Timing To Transmit the PTT ID
PTT ID Timing To Transmit the PTT ID
Off The PTT ID is not transmitted.
You can transmit Fleet (Own) and ID (Own)
BOT as the PTT ID when pressing the PTT
switch or the PF Ext. PTT (Voice) port.
You can transmit Fleet (Own) and ID (Own)
EOT as the PTT ID when releasing the PTT
switch or the PF Ext. PTT (Voice) port.
You can transmit Fleet (Own) and ID (Own)
Both as the PTT ID when pressing/releasing the
PTT switch or the PF Ext. PTT (Voice) port.
You can call the receiving party's PTT ID.
You can select the ID from 1 to 100 in
List 1 - 100
SelCall list. You can make a SelCall with
the Fleet and the ID.
Note:
" You can only select the ID configured in FleetSync > ID List for
List 1 - 100.
" The PTT ID is transmitted to make a voice communication. The
PTT ID is not transmitted when transmitting with the PF Data
PTT port and the PF Ext. PTT (Data) port.
94
!

22.1.1 Caller ID Display

This function allows you to display the received PTT ID on
the LCD.
A user can confirm the caller not only by voice, but also
through the display.
"CID" appears on the sub display when the transceiver
receives a PTT ID. The display returns to the channel
display after the Auto Reset Timer expires if the Auto
Reset Timer is configured. The display returns to normal
when pressing a key.
The ID is displayed when a PTT ID is received even when
the conditions for disabling the Mute function are not
(Refer to 14 PTT
satisfied.
You can configure the receive PTT ID to be displayed
using KPG-89D.
Note:
" You cannot reply to the ID displayed on the display.
" The PTT ID is displayed when receiving BOT or EOT.
!

22.1.2 PTT ID Sidetone

This tone sounds when the caller transmits the FleetSync
ID. This tone notifies the user of when the conversion is
possible after the PTT switch or the PF Ext. PTT (Voice)
port is pressed.
This function prevents the transceiver from missing calls
by starting the conversion during FleetSync PTT ID
transmission.
You can enable/disable this function using KPG-89D.
Note: When the PTT ID is configured to the channel, the Proceed
!
Function Reference
Configuration using KPG-89D
• Configuring the PTT ID (Channel) (Refer to FPRG
6.3.12 PTT ID.)
• Configuring the PTT ID (Group ID) (Refer to
FPRG 6.6.8 PTT ID.)
Configuration using KPG-89D
•
Configuring the Caller ID Display (Refer to FPRG
6.12.1 General 1 tab - Sub Display.)
Tone is disabled.
Configuration using KPG-89D
•
Configuring the PTT ID Sidetone (Refer to FPRG
6.12.1 General 1 tab - PTT ID Sidetone.)
Version: 1.11