Ptt Id; Ptt Id Type; Beginning Of Transmit; End Of Transmit - Kenwood TK-3180 Function Reference

14 PTT ID

This is the identification code transmitted when the PTT
switch is pressed and/or released.
By using this ID, the base station (dispatcher) can identify
the caller without asking for the caller's name.
You can configure the following items to PTT ID using
KPG-89D.
•

PTT ID Type

•

PTT ID (CH/GID Information)

•
Restricted ID in TA
14.1 PTT ID Type
You can select the PTT ID type. Select DTMF or
FleetSync as the PTT ID format.
You can select DTMF or FleetSync using KPG-89D.
You can configure the Beginning of Transmit and the End
of Transmit when the DTMF is selected.
Beginning of Transmit, 14.1.2 End of Transmit.)
You can configure the Fleet (Own) and the ID (Own)
when selecting FleetSync.
ID.)
!
Configuration using KPG-89D
• Configuring the PTT ID Type (Refer to FPRG
6.7.3 Common-Page 3 tab - PTT ID Type.)

14.1.1 Beginning of Transmit

You can configure the ID to be sent at the beginning of
transmit when the DTMF is selected.
You can configure the ID to be sent as the BOT using
KPG-89D. No ID will be transmitted if you do not
configure the BOT ID.
!
Configuration using KPG-89D
•
Configuring the Beginning of Transmit (Refer to
FPRG 6.7.3 Common-Page 3 tab - Beginning of
Transmit.)

14.1.2 End of Transmit

You can configure the ID to be sent at the beginning of
transmit when selecting DTMF.
You can configure the ID to be sent as the EOT using
KPG-89D. No ID will be transmitted if you do not
configure the content of the ID.
!
Configuration using KPG-89D
• Configuring the End of Transmit (Refer to FPRG
6.7.3 Common-Page 3 tab - End of Transmit.)
Version: 1.11
(Refer to 14.1.1
(Refer to 22.9.1 Own Fleet/
Function Reference
14.2 PTT ID
(CH/GID Information)
PTT ID (CH/GID Information) allows you to select the
timing to send the PTT ID.
You can enable/disable the PTT ID for each CH/GID
using KPG-89D. The following configuration is available.
Table 14-1 Timing to Transmit the PTT ID
(When the PTT ID Type is DTMF/ANI board.)
PTT ID Timing to Transmit the PTT ID
Off No PTT ID is transmitted.
This PTT ID is transmitted each time the
BOT
PTT switch is pressed.
This PTT ID is transmitted each time the
EOT
PTT switch is released.
This PTT ID is transmitted when the PTT
Both
switch is pressed and released.
Table 14-2 Timing To Transmit the PTT ID
(When the PTT ID Type is FleetSync.)
PTT ID Timing To Transmit the PTT ID
Off No PTT ID is transmitted.
Fleet (Own) and ID (Own) are transmitted as
BOT the PTT ID when the PTT switch or the PF
Ext. PTT (Voice) port is pressed.
Fleet (Own) and ID (Own) are transmitted as
EOT the PTT ID when the PTT switch or the PF
Ext. PTT (Voice) port is released.
Fleet (Own) and ID (Own) are transmitted as
the PTT ID when the PTT switch or the PF
Both
Ext. PTT (Voice) port is pressed and
released.
You can make an individual call. You can
List 1 - 100 select the ID from 1 to 100 in the SelCall list.
(FleetSync only) You can make a SelCall using the Fleet and
the ID.
Table 14-3 Timing to Transmit the PTT ID
(When the PTT ID Type is ANI board.)
PTT ID Timing To Transmit the PTT ID
Off No PTT ID is transmitted.
This ANI code of the ANI Board is sent. The
On timing to transmit the PTT ID must be
configured to the ANI board.
Note:
" "List 1 - 100" and "On" do not appear when selecting "DTMF"
using the PTT ID pulldown menu.
" "On" will not appear when selecting "FleetSync" using the PTT
ID pulldown menu.
" "BOT", "EOT", "Both", and "List 1 - 100" do not appear when
selecting "ANI Board" using the PTT ID pull-down menu.
49