Adjustment; Service Mode - Roland VersaCAMM VP-540 Service Notes

4 Adjustment

4-1 SERVICE MODE

[ ], [ ], [ ] + POWER ON
SERVICE MENU PRINT MENU
PRINT MENU HEAD RANK
PRINT MENU
HEAD ADJUST
MENU
[ MENU ] key
SERVICE MENU
HEAD RANK
HEAD 1
HEAD RANK
HEAD 4
HEAD ADJUST
BIAS
HEAD ADJUST
VERTICAL
HEAD ADJUST
HORIZONTAL
HEAD ADJUST
BI-DIR.DEFAULT
HEAD ADJUST
STANDARD HEAD
This menu is used for adjusting Head Alignment. Refer to [4-4 HEAD ALIGNMENT].
HEAD RANK 1
This menu is used for entering the Head Rank for each head
1234567 (1/5) with 35 digit number and alphabet. The digits can be changed
with [
[
under bar. Press [ENTER] key to save the settings.
HEAD RANK 4
It beeps for alerting when the calculation for verification,
CHECK SUM, is not correct in order to avoid input error.
1234567 (1/5)
BIAS PERFORMING
TEST PRINT
Feeds media for visual check of the test pattern, by pressing
[
BIAS
pressing [
to the original position.
--- VIEW ---
VERTICAL PERFORMING
TEST PRINT
Feeds media for visual check of the test pattern, by pressing
[
VERTICAL
pressing [
to the original position.
--- VIEW ---
HORIZONTAL
PERFORMING
TEST PRINT
HORIZONTAL
DT1, Low
HORIZONTAL
DT3, Low
Only for VP-540
HORIZONTAL
DT1, High
HORIZONTAL
DT3, High
Cursor can be moved with [ ] and [
keys. [ENTER] key for saving the setting. The value being selected is marked with an under bar.
It returns to the former menu by pressing [
It starts with H2 when H1 is defined as the standard head.
Default: 0 Range: -30 to +30dot (changeable by 0.5dot) 0.5dot is indicated as 1/2.
BI-DIR.DEFAULT TEST PRINT
TEST PRINT
Cursor can be moved with [
turned ON/OFF with [
start the test print of the selected heads. It returns to the former menu
by pressing [
BI-DIR.DEFAULT
DT1, Low
BI-DIR.DEFAULT
DT3, Low
Only for VP-540
BI-DIR.DEFAULT
DT1, High
BI-DIR.DEFAULT
DT3, High
Cursor can be moved with [ ] and [
[ENTER] key for saving the setting. The value being selected is marked with an under bar.
It returns to the former menu by pressing [
Default: 0) It can be changed starting from the standard value (15) with [
* * (
Range: 0 to +60dot (changeable by 0.5dot which is indicated as 1/2.
STANDARD HEAD
1 > 1
4-1
] and [ ] keys and parameters can be changed with
] and [ ] keys. The digit being changed is marked with an
TEST PRINT
] or [ ] keys while in [TEST PRINT] menu. Also by
] or [ ] keys again after feeding, media returns
TEST PRINT
] or [ ] keys while in [TEST PRINT] menu. Also by
] or [ ] keys again after feeding, media returns
TEST PRINT
H2 H3 H4
2 1 3
H2 H3 H4
2 1 3
H2 H3 H4
2 1 3
H2 H3 H4
2 1 3
] keys, and value can be selected with [
] key when the cursor is on the head of the left end.
PERFORMING
1234 TEST PRINT
] and [ ] keys, and the heads can be
] and [ ] keys. Press [ENTER] key to
] key when the cursor is on the head 1.
H1 H2 H3 H4
2 1 3 2
H1 H2 H3 H4
2 1 3 2
H1 H2 H3 H4
2 1 3 2
H1 H2 H3 H4
2 1 3 2
] keys, and value can be selected with [ ] and [
] key when the cursor is on the head of the left end.
] and [
This menu is hidden normally.
It appears when Base Head Menu is enabled
on Bit6 of PAGE2 in SYSTEM SWITCH menu.
] and [ ]
] keys.
] keys.