Roland VersaCAMM VP-540 Service Notes page 145

SERVICE MENU CUTTING MENU
CUTTING MENU CROPMARK SENSE
CUTTING MENU
FORCE ADJUST
CUTTING MENU
CROP-CUT ADJ.
CUTTING MENU
PRINT-CUT ADJ.
SERVICE MENU FRSHODPULWwab
SENSOR CHECK ***
This menu displays the real-time status of each sensor. It shows [ ] when the sensor is ON.
The first page shows the status of each sensor. Each alphabet stands for as follows.
F: Front Paper Sensor
R: Rear Paper Sensor
S: Crop Mark Sensor
H: Head Lock Sensor
O: Limit Sensor
D: Side Cover Sensor
P: Maintenance Cover Sensor
THERMISTOR CHK
SERVICE MENU
THERMISTOR CHK
HEAD:25 C/ 77 F
CROPMARK SENSE
OUTLEVEL CHECK
CROPMARK SENSE
ADJUST
FORCE ADJUST
30gf
FORCE ADJUST
200gf
CROP-CUT ADJ.
TEST PRINT
CROP-CUT ADJ.
SETTING
CROP-CUT ADJ.
TEST PRINT 2
PRINT-CUT ADJ.
TEST PRINT
PRINT-CUT ADJ.
SETTING
PRINT-CUT ADJ.
TEST PRINT 2
1234
H * *EC
*
Head Up/Down Sensor (VP-300: Fixed)
U: Head Up/Down Sensor
L: Sheet Load Sensor H: Head HIGH
W: Pinch Roller Sensor L: Head LOW
w: Wiper Sensor
TU Motor Drive Sensor
a: TU Motor Drive Sensor
(When TU is connected)
b: Not in use Blank: Not driving
This is for checking Thermistor. It displays the temperature read from the thermistor placed on the board of the Head1.
The temperature on the left is in Celsius and the right is in Fahrenheit.
Since the temperature of the device possibly rises, it normally shows higher temperature than the room temperature.
MIN 0.7V MAX2.3
[2.0V ]
This is for adjusting the level of Crop Mark Sensor.
Refer to [4-8 CROP MARK SENSOR ADJUSTMENT].
ADJUST
+2 +1
This is for adjusting the Crop Mark Sensor sensitivity. There are 3 levels of sensitivity, 0, +1 and +2.
This adjustment may help when Crop Mark detection is failed with the default level setting.
Default: 0
30gf
17 16
200gf
56 57
PERFORMING
TEST PRINT
F:+0.30 +0.30mm
S:-0.40 -0.40mm
Returns to menu with [MENU] key
PERFORMING
TEST PRINT
PERFORMING
TEST PRINT
F:+0.30 +0.30mm
S:-0.40 -0.40mm
Returns to menu with [MENU] key
PERFORMING
TEST PRINT
The second page shows the status of each
Cartridge Sensor and Ink Empty Sensor.
Each color has 2 positions and the left side
on the display shows the left-side head.
Blank: Cartridge not inserted, Ink remains
C: Cartridge inserted, Ink remains
E: Cartridge not inserted, Ink empty
: Driving
*
: Cartridge inserted, Ink empty
*
4-4
This is for adjusting the Tool Pressure.
Refer to [4-13 TOOL PRESSURE ADJUSTMENT].
30gf Range: 0 to 30 Default: 17
200gf Range: 31 to 80 Default: 56
This test pattern is for adjusting the cut position
during automatic Crop Mark detection. It prints a
square Crop Mark and cuts the contour after
detecting the mark.
When it shows [ ], it means that it has never
*****
been setup and it needs to be set. In this case, even
if adjustment is unnessesary due to the test result,
[0] must be set here.
This test pattern is for adjusting the cut position
during automatic Crop Mark detection. It prints a
square Crop Mark and continuously prints 0.1mm
scales for both scan and feed direction, and then
cuts crosswise after detecting the mark.
This test pattern is for adjusting the print & cut
position. It prints 3 square Crop Marks along the
scan direction and cuts the contours of the marks.
When it shows [ ], it means that it has never
*****
been setup and it needs to be set. In this case, even
if adjustment is unnessesary due to the test result,
[0] must be set here.
This test pattern is for adjusting the print & cut
position. It prints 0.1mm scales for both scan and
feed direction and then cuts crosswise.