Roland VersaCAMM VP-540 Service Notes page 143

This is for adjusting the flushing position. For VP-540, set the head height to LOW.
As entering the menu, the Head Carriage moves to the current flushing position. With [left] and [right] keys, move the Head Carriage to the position where
the surface of the leftmost Cap Top slightly touches the Head Surface, and press [ENTER] key to save the position. As [ENTER] key is pressed, the head is
automatically capped and it backs out the menu. For backing out the menu without saving the position, press [MENU] key without pressing [ENTER] key.
SERVICE MENU
I/S MENU
PRINT MENU
LINEAR ENCODER
This is for checking the installation and
operation of Linear Encoder and Scale.
Refer to [4-6 LINEAR ENCODER SETUP].
PRINT MENU
LINEAR CALIB.
Revised 7
This is for calibrating the cutting size in the scan
direction by calculating the expansion and contraction
amount of the Encoder Scale.
PRINT MENU
CALIB.DEFAULT
PRINT MENU
TEST PATTERN
PRINT MENU
FLUSHING ADJ.
I/S MENU
I/S CHECK
I/S MENU
PUMP CHECK
I/S MENU
I/S CONTROL
I/S MENU
WIPER AGING
NOW PROCESSING..
POS: 1361.00mm
NOW PROCESSING..
CALIB.DEFAULT
TEST PRINT
CALIB.DEFAULT
SETTING
TEST PATTERN
HORIZONTAL
TEST PATTERN
BI-DIR.
TEST PATTERN
FILL
TEST PATTERN
BI-DIR. CHECK
NOW PROCESSING..
NOW PROCESSING..
Checking
PUMP CHECK
PUMP SUCTION
PUMP CHECK
PUMP RELEASE
I/S CONTROL
WIPER
NOW PROCESSING..
4-2
Normal (beeps 1 time)
LINEAR ENCODER
SETUP COMPLETED
Error (beeps 2 times)
LINEAR ENCODER
Error is found on Linear
Encoder and Scale.
SETUP FAILED
Normal (beeps 1 time)
LINEAR CALIB.
SETUP COMPLETED
LINEAR CALIB.
0.18%
Error (beeps 2 times)
LINEAR CALIB.
FAILED TO SETUP
PERFORMING
This menu is used for Calibration.
Refer to [4-11 CALIBRATION].
TEST PRINT
When it shows [
that it has never been setup and it
SETTING
needs to be set. In this case, even if
+0.05% +0.10%
adjustment is unnecessary by the
test result, [0] must be set here.
PERFORMING
This is for checking the Head
Alignment in Horizontal.
TEST PRINT
This is for checking the Head
PERFORMING
Alignment in Bidirectional.
TEST PRINT
It prints on the entire print range
PERFORMING
with solid single color by each
head. Print mode is fixed at 720
TEST PRINT
dpi and 8 pass.
This print pattern is for checking a
PERFORMING
shifting error in Bidirectional and
TEST PRINT
also for confirming the mechanical
tendency.
FLUSHING ADJ.
SET POSITION
Normal
I/S CHECK
COMPLETED
Error
I/S CHECK ERROR
WIPER
NOW PROCESSING..
This is for checking the pump
motor. The rotation for both ink
suction and release can be
checked. Pump motor rotates
for 5 seconds and stop.
NOW PROCESSING..
The wiper can be moved
manually. Option: FRONT/REAR
Default: FRONT
WIPER
Caution: Make sure not to have
FRONT
the Head Carriage and Tool
carriage above the wiper unit
during this operation.
Normal
WIPER AGING
COMPLETED
Error (beeps 2 times)
WIPER AGING
FAILED !!
], it means
*****
NOW PROCESSING..
This is for checking the
operation of the wiper motor
and sensor. Make sure not
to have the Head Carriage
and Tool Carriage above the
wiper unit during the check.
This is for confirming that the
wiper is operated properly.