Lucent technologies Stinger MRT 19 Manuals

Customer Service

3

Table of Contents

5

About this Guide

17

Chapter 1 Introduction to the Stinger MRT

21

Chapter 2 Preparing for the Installation

25

Chapter 3 Installing a Stinger MRT

36

Chapter 4 Determining the Operating Status

61

Chapter 5 Stinger MRT Operational Overview

69

Chapter 6 Configuring Administrative Access, System Timing, and Startup Settings

77

Administrative Configuration Overview
77
Making the Initial Administrative Connection
78
Figure 6-1 Serial Management Connection to the Stinger MRT
78
Logging into the Stinger MRT
79
Restricting Administrative Access
79
Providing a Basic System IP Configuration
82
Additional Administrative Connections and Configuration
85
Configuring System Clocking (Optional)
95
- Using the BITS Clock Source
  95
  - Loss of BITS Signal Indications and Fall-Back
    95
  - Changing the BITS Clock Source
    96
- Using a Trunk Module Clock Source
  97
  - Configuring Trunk Ports as Eligible Clock Sources
    97
  - Typical Trunk Port Clock Source Configurations
    98
Retaining Basic Configuration Settings for Remote Administration
98
- Storing a Partial Configuration for Restart after Clearing NVRAM
  98
  - Allowing Password Information in the Default.cfg File
    99
  - Creating the Default.cfg File
    99
- Restarting with a Partial Configuration
  100
Saving and Loading a Backup Configuration
100
- Saving the Configuration
  100
  - Saving the Full Configuration to a Local File
    101
  - Saving the Configuration to a Network Host
    101
- Restoring the Configuration
  101
  - Restoring from a Local File
    101
  - Restoring from a Network Host
    102

Chapter 7 Configuring the ADSL Line Interfaces

103

Chapter 8 Configuring the SHDSL Line Interfaces

121

Configuring SHDSL Interfaces
121
- Configuring Port Settings for SHDSL
  122
- Sample SHDSL Mode Configuration
  129
- Binding Two SHDSL Ports
  129
- Displaying SHDSL Port Status
  130
Configuring Call Control
131
Checking the Status of an SHDSL Interface
132
- Checking the Status of the Physical Interface
  133
- Obtaining Statistics about Operations
  134
Diagnostic Internal, External, and Bit Error-Rate Tests
136
- Configuring an Internal Diagnostic Test (IDT)
  138
- Configuring a Bit-Error-Rate Test (BERT)
  139
- Configuring an External Diagnostic Test (EDT)
  139
  - Digital Loopback
    140
  - Analog Loopback
    140
  - Figure 8-1 Digital Loopback
    140
  - Figure 8-2 Analog Loopback
    140
- Interface Standards
  141
- Embedded Operations Channel (EOC) Protocol Compliance
  141

Chapter 9 Configuring T1 and E1 Trunk Modules

143

Chapter 10 Configuring an OC3-ATM Trunk Module

185

Chapter 11 Configuring a DS3-ATM Trunk Module

199

Appendix A Stinger MRT Intended Use

211

Appendix B Hosted Operation of Cascaded Stinger MRT Units

213

Appendix C Cables and Connectors

239

Appendix D Safety-Related Electrical, Physical, and Environmental Information

253

Index

259

Lucent Technologies Stinger MRT 19 Manuals

Lucent Technologies Stinger MRT 19 Getting Started Manual (264 pages)

Table of Contents

About this Guide

Chapter 1 Introduction to the Stinger MRT

Chapter 2 Preparing for the Installation

Chapter 3 Installing a Stinger MRT

Chapter 4 Determining the Operating Status

Chapter 5 Stinger MRT Operational Overview

Chapter 6 Configuring Administrative Access, System Timing, and Startup Settings

Chapter 7 Configuring the ADSL Line Interfaces

Chapter 8 Configuring the SHDSL Line Interfaces

Chapter 9 Configuring T1 and E1 Trunk Modules

Chapter 10 Configuring an OC3-ATM Trunk Module

Chapter 11 Configuring a DS3-ATM Trunk Module

Appendix A Stinger MRT Intended Use

Appendix B Hosted Operation of Cascaded Stinger MRT Units

Appendix C Cables and Connectors

Appendix D Safety-Related Electrical, Physical, and Environmental Information

Index

Related Products

Lucent Technologies Categories