Menu Configuration And Content - Ikegami HC-HD300 Operation Manual

Menu Configuration and content

The following lists the camera menu configuration.
■ MENU (Simple Menu)
The simple menu is the same as MENU (1/4) described below. Refer to items in MENU (1/4) for details of each menu.
■ MENU (1/4)
Menu Item
VF DISPLAY
― DISPLAY MODE
― MARKER/CHAR LVL
― FRAME MARKER
― VF ASPECT
― SIDE MASK
― CONTRAST
― BRIGHT
― SAFETY AREA
― SAFETY MARKER
― CENTER MARKER
― FOCUS INDICATE
― ZOOM INDICATE
― AUTO VF ASPECT
ZEBRA INDICATOR
― ZEBRA1 DETECT
― ZEBRA2 IND
― ZEBRA2 DETECT
ZEBRA IND LVL
VF DTL
― BOOST FREQ
― NOISE SUP
― VF DTL
V FILTER
VF MODE
― COLOR VF MODE
― VF VIDEO SELECT
FRONT TALLY
Initial
Setting value
setting
2 OFF, 1, 2
100 0 to 100
ON-16:9, ON-14:9,
OFF
ON-13:9, ON-4:3, OFF
16:9 16:9, 4:3
OFF, ON-4:3,
OFF
ON-13:9, ON-16:9
50 0 to 100
60 0 to 100
ACTION ACTION, TITLE
ON-16:9 ON-4:3, ON-16:9, OFF
TYPE1, TYPE2, TYPE3,
TYPE1
OFF
ON ON, OFF
ON ON, OFF
OFF ON, OFF
100% 30 to 109%
OFF ON, OFF
70% 30 to 109%
78 1 to 100
10MHz, 15MHz, 18MHz,
10MHz
18MHzWIDE
5 0 to 10
35 0 to 100
OFF ON, OFF
AUTO AUTO, ON
Y Y, R, G, B, R+G+B,
( *2 R/G/B) (R/G/B)
ENABLE ENABLE, DISABLE
HC-HD300 1412 VER1 (U)
5.2 Settings from the Menu
Description, Remarks
1 : Only the markers are constantly displayed.
Information related to characters is displayed for
2 seconds during function operation and when
changing parameters.
2 : The markers and characters are displayed at all times.
OFF : The markers and characters are constantly OFF, and
only the warning messages are displayed.
Sets the brightness levels of the markers and characters. The
brightness level gets dark in the direction of "1".
Sets the frame marker.
Sets the VF aspect ratio.
Sets the side mask.
Adjusts the side mask contrast level.
Adjusts the side mask brightness level.
ACTION : Area marker of 93% of the screen height and width.
TITLE : Area marker of 89% of the screen height and width.
Sets the safety marker.
Sets the center marker.
Only active when using the serial lens.
Only active when using the serial lens.
Switches the VF aspect ratio in linked motion with the output
mode of the BS/CCU down converter.
Overlaps the striped pattern signal on the image if the image
level has exceeded the individual DETECT LEVELS. The
zebra indicator goes ON/OFF with the VF special switch.
-Zebra 1 signal : Fine, slanted striped pattern signal flowing
toward the upper right of the screen.
*Use to control the tone of the entire screen.
-Zebra 2 signal : Thick, slanted striped pattern signal
flowing to the lower right of the screen.
* Used for controlling the tone of the
subject, such as face tone, etc
Sets the DETECT LEVEL of the 1st zebra indicator.
Selects whether there is a 2nd zebra indicator or not.
Sets the DETECT LEVEL of the 2nd zebra indicator.
Adjusts the overlap level of the zebra indicator.
Adjusts the overlap amount of the VF image focusing edge
signal (VF DTL).
Selects the frequency to be boosted.
Sets the removal level of the noise signal.
Sets the VF detail amount. The detail amount decreases in
the direction of "0" and increases in the direction of "100".
Turns on/off the filter of VF DTL.
AUTO : Automatically recognizes the color VF to convert
the VF VIDEO signal to R/G/B output.
ON : Makes the VF VIDEO signal output R/G/B.
Sets the VF image output.
R/G/B can be set in case the color VF is mounted or when
the COLOR VF MODE is ON.
Sets active/inactive for VF FRONT TALLY.
*1
MENU DATA
ALL VF
○ ○
○ ○
○ ○
○ ○
5
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
81