Menu Configuration And Content - Ikegami HDK-65C Operation Manual

Menu Configuration and content
The following lists the camera menu configuration.
■ MENU (Simple Menu)
The simple menu is the same as MENU (1/3) described below. Refer to items in MENU (1/3) for details of each menu.
■ MENU (1/3)
Menu Item
VF DISPLAY
― DISPLAY MODE
― VF DTL
― MARKER/CHAR LVL
― FRAME MARKER
― VF ASPECT
― SIDE MASK
― CONTRAST
― BRIGHT
― SAFETY AREA
― SAFETY MARKER
― CENTER MARKER
― FOCUS INDICATE
― ZOOM INDICATE
― AUTO VF ASPECT
ZEBRA INDICATOR
― ZEBRA1 DETECT
― ZEBRA2 IND
― ZEBRA2 DETECT
ZEBRA IND LVL
VF DTL
― BOOST FREQ
NOISE SUP
MIC GAIN CONTROL
― MIC1 STEP
― MIC1 FINE
― MIC2 STEP
MIC2 FINE
Initial
Setting value
setting
2 OFF, 1, 2
35 1 to 100
100 1 to 100
ON-16:9, ON-14:9, ON-
OFF
13:9, ON-4:3, OFF
16:9 16:9, 4:3
OFF, ON-4:3, ON-13:9,
OFF
ON-16:9
50 0 to 100
60 0 to 100
ACTION ACTION, TITLE
ON-16:9 ON-4:3, ON-16:9, OFF
ON ON, OFF
ON OFF, ON
ON OFF, ON
OFF ON, OFF
100% 30 to 109%
OFF OFF, ON
70% 30 to 109%
78
10MHz,15MHz,
10MHz
18MHz,18MHzWIDE
0 0 to 10
+4dB, 0dB, -10dB,
-40dB -20dB, -30dB, -40dB,
-50dB, -60dB
0 -100 to 100
+4dB, 0dB, -10dB,
-40dB -20dB, -30dB, -40dB,
-50dB, -60dB
0 -100 to 100
HDK-65C 1501 VER1 (U)
5.2 Settings from the Menu
Description, Remarks
OFF : The markers and characters are constantly OFF, and
only the warning messages are displayed.
1 : Only the markers are constantly displayed.
Information related to characters is displayed for
2 seconds during function operation and when
changing parameters.
2 : The markers and characters are displayed at all times.
Sets the VF detail amount. The detail amount decreases in
the direction of "0" and increases in the direction of "100".
Sets the brightness levels of the markers and characters. The
brightness level gets dark in the direction of "1".
Sets the frame marker.
Sets the VF aspect ratio.
Sets the side mask.
Adjusts the side mask contrast level.
Adjusts the side mask brightness level.
ACTION : Area marker of 93% of the screen height and width.
TITLE : Area marker of 89% of the screen height and width.
Sets the safety marker.
Sets the center marker.
Only active when using the serial lens.
Only active when using the serial lens.
Switches the VF aspect ratio in linked motion with the
output mode of the BS/CCU down converter.
Overlaps the striped pattern signal on the image if the image
level has exceeded the individual DETECT LEVELS.
The zebra indicator goes ON/OFF with the VF special
switch.
-Zebra 1 signal : Fine, slanted striped pattern signal flowing
toward the upper right of the screen.
Use to control the tone of the entire screen.
-Zebra 2 signal : Thick, slanted striped pattern signal
flowing to the lower right of the screen.
Used for controlling the tone of the subject,
such as face tone, etc
Sets the DETECT LEVEL of the 1st zebra indicator.
Selects whether there is a 2nd zebra indicator or not.
Sets the DETECT LEVEL of the 2nd zebra indicator.
Adjusts the overlap level of the zebra indicator.
Adjusts the overlap amount of the VF image focusing edge
signal (VF DTL).
Selects the frequency to be boosted.
Sets the removal level of the noise signal.
The MIC1 gain is changed step by step.
Fine adjustment of the MIC1 gain. The gain decreases about
-8 dB with -100, and increases about +8 dB with +100.
The MIC2 gain is changed stepwise.
Fine adjustment of the MIC2 gain. The gain decreases about
-8 dB with -100, and increases about +8 dB with +100.
*1
MENU DATA
ALL VF
5
-
-
-
-
85