Ikegami HC-HD300 Operation Manual page 98

5.2 Settings from the Menu
Menu Item
FOCUS ASSIST
― ASSIST AREA
― TRIGGER
― AREA ON/OFF SW
― VF DOT BY DOT
― FOR RET
― ASSIST DATA
ASSIST DATA SETTING
― SW ACTION
― AREA DISP TIME
― AREA SIZE
― AREA LEVEL
― AREA COLOR
― AREA MARKER
EDGE BOOST
―
LEVEL
― EDGE COLOR
STORE DATA
MIC GAIN CONTROL
― MIC1 STEP
― MIC1 FINE
― MIC2 STEP
MIC2 FINE
RETURN SELECT MODE
― RET-2/MIC SEL
― VTR SW SEL
RET PRIORITY
FILTER SERVO MODE
SERVO CONT
82
Initial
Setting value
setting
TRIGGER TRIGGER ON,
ON ALWAYS ON, OFF
FOCUS, FOCUS/ZOOM,
FOCUS
LENS VTR
VTR SW, EXT SW,
NONE
NONE"
UNLINK LINK, UNLINK
ON ON, OFF
NO.1 N0.1 to N0.4
ALTERNATE,
ALTERNATE
MOMENTARY
0.5S to 5.0S
1.0S
(0.5sec increments)
15 0 to 100
60% 25% to 100%
MONO MONO, COLOR, NEGA
OFF ON, OFF
55 0 to 100
MONO, CYAN,
MONO MAGENTA, YELLOW,
GREEN, RED, BLUE
--- N0.1 to N0.4
+4dB, 0dB, -10dB,
-40dB -20dB, -30dB, -40dB,
-50dB, -60dB
0 -100 to 100
+4dB, 0dB, -10dB,
-40dB -20dB, -30dB, -40dB,
-50dB, -60dB
0 -100 to 100
RET-2 RET-2, MIC
RET-2, MIC,
RET-2
FOCUS ASST
NOTHING, RET-1,
NOTHING
RET-2
SERVO SERVO, MANUAL
HC-HD300 1412 VER1 (U)
Description, Remarks
Sets the ASSIST AREA display.
Select TRIGGER ON if you wish to display with the trigger
of lens operation, etc.
Trigger to display ASSIST AREA.
This setting is used when TRIGGER ON is selected.
Selects the switch to turn ON/OFF the ASSIST AREA.
Sets whether a control signal is sent to a VF having a DOT
BY DOT display function.
Sets whether to display the ASSIST AREA or not when
switching to the RET signal.
Selects the ASSIST DATA compiled in the ASSIST DATA
SETTING menu.
If the trigger has been assigned to the LENS VTR SW, sets
whether it is momentary operation or alternate operation.
Sets the time from trigger detection until the focus assist area
is erased.
Sets the focus assist area range.
If set to "100", it is the entire screen domain.
Sets the image level of the ASSIST AREA.
Sets whether the ASSIST AREA image should be color,
monochrome or negative.
Sets whether the assist area frame marker is displayed or not.
Sets the boost level of the edge signal.
Sets the color of the edge signal.
The contents set in the ASSIST DATA SETTING menu are
stored as ASSIST DATA. Select the numbers you wish to
store from No. 1 to No. 4 and write over the present data to
store them.
The MIC1 gain is changed step by step.
Fine adjustment of the MIC1 gain. The gain decreases about
-8 dB with -100, and increases about +8 dB with +100.
The MIC2 gain is changed stepwise.
Fine adjustment of the MIC2 gain. The gain decreases about
-8 dB with -100, and increases about +8 dB with +100.
Allocates a function to the RET-2/MIC button on top of
handle and on left side of camera.
Sets a function to the VTR SW button on the lens.
If the FOCUS ASSIST menu TRIGGER is set to LENS VTR,
it becomes FOCUS TRIG fixed (information display).
If a RET-1 or RET-2 image is not displayed in the viewfinder,
sets the output signal to MON SDI (during RETURN
setting).
NOTHING : Sets to RET image last displayed in VF.
RET1 : Sets to RET-1 image.
RET2 : Sets to RET-2 image.
SERVO : Sets to automatic control.
MANUAL : Sets to manual control.
MENU DATA
ALL VF
× ×
× ×
× ×
× ×
× ×
× ×
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
‐ ‐
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×