Ikegami HC-HD300 Operation Manual page 106

5.2 Settings from the Menu
■ ENGINEER (1/2)
Menu Item
AUTO DPC
― DPC
― DETECT MODE
― SAMPLE AREA SET
― AUTO DPC
― DPC EFFECT CHK
― DPC CLEAR
― SAMPLE GUIDE LINE
AREA SELECT SPEED
FIBER SINGLE MODE CONT
SINGLE MODE
CAMERA ID SETUP
― PROGRAM NO.
ID NO.
MATRIX PRESET DATA
― MATRIX 1
― MATRIX 2
MATRIX 3
MATRIX USER1 DATA SET
― DATA SET MODE
― R-G
― R-B
― G-R
― G-B
― B-R
― B-G
DATA CLEAR
90
Initial
Setting Value
Setting
ON ON, OFF
WHT+BLK, WHITE,
WHT+BLK
BLACK
OK OK, CANCEL
OK OK, CANCEL
ALL ON, H ON, V ON,
ALL ON
ALL OFF
FAST FAST, NORMAL
OFF ON, OFF
1 1 to 99, OFF
1 1 to 40
OFF, SMPTE, EBU,
Destination
ITU-709,
setting
(USER1, USER2)
OFF, SMPTE, EBU,
Destination
ITU-709,
setting
(USER1, USER2)
OFF, SMPTE, EBU,
Destination
ITU-709,
setting
(USER1, USER2)
OFF ON, OFF
0.0 -100 to +100
0.0 -100 to +100
0.0 -100 to +100
0.0 -100 to +100
0.0 -100 to +100
0.0 -100 to +100
--- READY
HC-HD300 1412 VER1 (U)
Description, Remarks
Turns on/off all data with defective pixel correction.
ON : Enable all data with defective pixel correction.
OFF : Disable all data with defective pixel correction.
Sets the mode of defective pixel correction.
WHT + BLK : Simultaneously corrects white and black
defective pixels.
WHT : Corrects white defective pixels only.
BLK : Corrects black defective pixels only.
Sets the WINDOWS cursor for defective pixel correction.
If this item is selected, automatic detection and automatic
correction are performed for defective pixel correction.
You can check the correction of defective pixels in all
setting ranges.
Deletes all correction data for defective pixel correction.
Selects display/hide and types of auxiliary line on
WINDOWS cursor in "SAMPLE AREA SET".
Sets the moving speed of WINDOWS cursor in "SAMPLE
AREA SET".
Supplies power from DC connector of adapter when BS/
CCU is connected. In this case, stops power supply from an
optical cable.
If it is sets to "ON," the mode is switched to the single fiber
mode.
You can set the camera No. at the time of program operation,
etc.
If the camera No. is set on the operation control panel side,
the ID No. that has been set is displayed.
Reversely, if the camera No. is set on the camera side, the ID
No. that has been set is displayed on the operation control
panel.
Sets ID No. of camera. Sets this when you want the camera
No. to be detected and displayed on the BS/CCU side.
Selects the preset of color matrix.
* In order to select USER1 and 2, you must turn on
"MATRIX USER1(2) DATA SET - DATA SET MODE".
Sets the preset (USER1) of color matrix.
ON : Sets the preset data.
OFF : Does not set the preset data.
Sets the matrix of R-G.
Sets the matrix of R-B.
Sets the matrix of G-R.
Sets the matrix of RG-B.
Sets the matrix of B-R.
Sets the matrix of B-G.
READY : Normal status
PUSH SET → CLR : Clears the preset data.
CANCEL : Exit "DATA CLEAR" without clearing
the settings.
MENU DATA
ALL VF
× ×
× ×
- -
- -
- -
- -
○ ×
× ×
○ ×
× ×
× ×
○ ×
○ ×
○ ×
- -
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
- -